Electrolux CFMV156DBD Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 48

Electrolux CFMV156DBD Скачать руководство пользователя страница 7

7

CFMV156DBD

CFMV156DSD

CFMV156DCE

PRODUCT DESCRIPTION

GENERAL INFORMATION

OPERATION

TROUBLESHOOTING GUIDE AND

TEST PROCEDURE

TOUCH CONTROL PANEL

COMPONENT REPLACEMENT

AND ADJUSTMENT PROCEDURE

WIRING DIAGRAM

PARTS LIST

SERVICE MANUAL

ELECTROLUX

OVER THE RANGE

MICROWAVE OVEN

CFMV156DBD / CFMV156DSD

CFMV156DCE

FOREWORD

This Manual has been prepared to provide Electrolux Home Products
Service Personnel with Operation and Service Information for the ELEC-
TROLUX OVER THE RANGE MICROWAVE OVENS, CFMV56DBD,
CFMV56DSD, and CFMV56DCE.

It is recommended that service personnel carefully study the entire
text of this manual so that they will be qualified to render satisfactory
customer service.

Check the interlock switches and the door seal carefully. Special atten-
tion should be given to avoid electrical shock and microwave radiation
hazard.

WARNING

Never operate the oven until the following points are ensured.
(A) The door is tightly closed.
(B) The door brackets and hinges are not defective.
(C) The door packing is not damaged.
(D) The door is not deformed or warped.
(E) There is not any other visible damage with the oven.

Servicing and repair work must be carried out only by trained service
personnel.

DANGER

Certain initial parts are intentionally not grounded and present
a risk of electrical shock only during servicing. Service person-
nel - Do not contact the following parts while the appliance is
energized;
High Voltage Capacitor, Power Transformer, Magnetron, High
Voltage Rectifier Assembly, High Voltage Harness;
If provided, Vent Hood, Fan assembly, Cooling Fan Motor.

All the parts marked “ * ” on parts list are used at voltages more
than 250V.

Removal of the outer wrap gives access to voltage above 250V.

All the parts marked “

∆

” on parts list may cause undue microwave

exposure, by themselves, or when they are damaged, loosened or
removed.

NOTES

ELECTROLUX CANADA CORPORATION

«
...
5
6
7
8
9
...
»

Содержание CFMV156DBD

















































Отзывы:

Нет отзывов