manualshive.com logo in svg

Electrolux CFMV156DBD, Руководство по обслуживанию

Электролюкс CFMV156DBD - мощный и удобный в использовании микроволновый духовой шкаф. Ищите сервисный мануал или инструкцию по эксплуатации? Скачайте их бесплатно с manualshive.com. Получите подробные руководства по обслуживанию и эксплуатации этого высококачественного продукта для вашего дома.

Поделиться
Скачать
background image

P/N 316439259

Publication # 5995505418

CFMV156DBD

CFMV156DSD

CFMV156DCE 

In the interest of user-safety the oven should be restored to its original condition and only parts identical to those specified should 
be used.

WARNING TO SERVICE PERSONNEL: Microwave ovens contain circuitry capable of producing very high voltage 
and current. Contact with the following parts may result in a severe, possibly fatal, electrical shock. (High Voltage 
Capacitor, High Voltage Power Transformer, Magnetron, High Voltage Rectifier Assembly,  High Voltage Harness 
etc..)

TABLE OF CONTENTS

Page

PRECAUTIONS TO BE OBSERVED BEFORE AND DURING SERVICING TO
AVOID POSSIBLE  EXPOSURE TO EXCESSIVE MICROWAVE ENERGY..................... INSIDE FRONT COVER
BEFORE SERVICING ....................................................................................................... INSIDE FRONT COVER
WARNING TO SERVICE PERSONNEL................................................................................................................. 3
MICROWAVE MEASUREMENT PROCEDURE..................................................................................................... 4
FOREWORD AND WARNING ............................................................................................................................... 7
PRODUCT SPECIFICATIONS ............................................................................................................................... 8
GENERAL  INFORMATION.................................................................................................................................... 8
OPERATION......................................................................................................................................................... 
TROUBLESHOOTING GUIDE ............................................................................................................................. 5
TEST PROCEDURE ............................................................................................................................................ 7
TOUCH CONTROL PANEL ASSEMBLY .............................................................................................................. 27
COMPONENT REPLACEMENT AND ADJUSTMENT PROCEDURE................................................................. 3
PICTORIAL DIAGRAM......................................................................................................................................... 39
POWER UNIT CIRCUIT ....................................................................................................................................... 40
LSI UNIT CIRCUIT ............................................................................................................................................... 4
PRINTED WIRING BOARD.................................................................................................................................. 42
PARTS LIST  ........................................................................................................................................................ 43
PACKING AND ACCESSORIES .......................................................................................................................... 47

S64M242FM156C

CFMV156DBD

CFMV156DSD

CFMV156DCE

OVER THE RANGE

MICROWAVE OVEN

MODELS

CFMV56DCE

 ELECTROLUX 

SERVICE MANUAL

This document has been published to be used for after  sales service only. The contents are subject to 
 change without notice.

ElEctrolux canada corporatIon

6150 McLaughlin Road

,

Mississauga, Ontario, Canada L5R 4C2

Canada 866•294•9911 (English or French)

Содержание CFMV156DBD

















































Отзывы:

Нет отзывов

Похожие инструкции для CFMV156DBD

Omega OM30GX Instruction Manual preview
OM30GX
Бренд: Omega Страницы: 14
saro WD 900 Instruction Manual preview
WD 900
Бренд: saro Страницы: 4
Jenn-Air JJW9630DDW Installation Instructions Manual preview
JJW9630DDW
Бренд: Jenn-Air Страницы: 7
PROZIS Microcookin User Manual preview
Microcookin
Бренд: PROZIS Страницы: 39
Rangemaster Double Built in Oven Installation And User Manual preview
Double Built in Oven
Бренд: Rangemaster Страницы: 16
Teka MWE 207 FI Instruction Manual preview
MWE 207 FI
Бренд: Teka Страницы: 72
VALBERG MFO 66 P K CD 765C Instructions For Use Manual preview
MFO 66 P K CD 765C
Бренд: VALBERG Страницы: 67
R.G.V. FD1025 Instruction Manual preview
FD1025
Бренд: R.G.V. Страницы: 60
Westinghouse WLG510 Series Quick Start Manual preview
WLG510 Series
Бренд: Westinghouse Страницы: 2
GE JES1133WN Use And Care & Cooking Manual preview
JES1133WN
Бренд: GE Страницы: 28
Rubine IA8 User Manual preview
IA8
Бренд: Rubine Страницы: 13
Roper B9458B0 Use And Care Manual preview
B9458B0
Бренд: Roper Страницы: 18
DeLonghi EO12 Series Manual preview
EO12 Series
Бренд: DeLonghi Страницы: 87
NEFF B45M42 3 Series Instruction Manual preview
B45M42 3 Series
Бренд: NEFF Страницы: 28
NEFF B1DCC0A 0B Series Instruction Manual preview
B1DCC0A 0B Series
Бренд: NEFF Страницы: 32
Teka MCX 45 BIT Instructions For Use Manual preview
MCX 45 BIT
Бренд: Teka Страницы: 35
Orava Miwa Inox Instruction Manual preview
Miwa Inox
Бренд: Orava Страницы: 22
Samsung NV660 User Manual preview
NV660
Бренд: Samsung Страницы: 52

Бренды по названию

Популярные бренды

Загрузить еще бренды