Electrolux Professional Compass Pro TD6-10 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 44

background image

Installation manual

17

4.4

Drain connection (only for machines with heat pump)

Connect the drain to the heat pump unit.

Note!

The outlet condense water (4) and the cooling water (5) must be connected to separate outlets.
The hose (4) must be positioned over the water level in the floor drain.

Note!

The drain must be lower than the drain outlet from the heat pump unit. If not the water will flow back into the
machine. Adjust with the feet.
The hoses shall hang in gentle arcs.

4

5

fig.W00609

4.5

Water connection (only for machines with heat pump)

All water intake connections to the machine should be fitted with manual shut-off valves and filters, to facilitate instal-
lation and servicing.
Water pipes and hoses should be flushed clean before installation.
The machine shall be connected with new water hoses. Re-used water hoses must not be used.
Hoses are to be of an approved type and grade and comply with IEC 61770.
After installation hoses must hang in gentle arcs.
All connectors present on the machine must be connected.
Connect the water to the water cooling system (6).

6

W00609A

Water pressure:
Miniumum: 50 kPa (0.5 kp/cm

2

)

Maximum: 800 kPa (8 kp/cm

2

)

Recommended: 200–600 kPa (2–6 kp/cm

2

)

Note!

If the water pressure is below the minimum value, the drying result can not be guaranteed for certain
program.

«
...
15
16
17
18
19
...
»

Содержание Compass Pro TD6-10













































Отзывы:

Нет отзывов

Похожие инструкции для Compass Pro TD6-10

COMPACT PRO CV4802Y0

Бренд: Rowenta Страницы: 2

Instant Recovery 18 TS

Бренд: Keating Of Chicago Страницы: 2

Бренд: COMAC Страницы: 2

Бренд: anko Страницы: 11

Бренд: Ultrean Страницы: 12

Бренд: Henny Penny Страницы: 69

Бренд: Linea 2000 Страницы: 60

DOMO DELI FRYER XL 4 L

Бренд: Linea 2000 Страницы: 60

CHEF IDEE CI2X8L

Бренд: Bartscher Страницы: 25

Бренд: Mediclinics Страницы: 40

Бренд: Frigidaire Страницы: 10

Бренд: Frigidaire Страницы: 12

Бренд: Frigidaire Страницы: 6

Бренд: Frigidaire Страницы: 8

Бренд: Frigidaire Страницы: 18

Бренд: Frigidaire Страницы: 16

Бренд: Frigidaire Страницы: 31

Бренд: Frigidaire Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды