ElectroFlying eska Скачать руководство пользователя страница 1

Страница: 1 / 20

Electric Sport Aerobatic Park Flyer R/C Aircraft

Length: 26.5“ • Wing Span: 31” • Wing Area: 230 sq. in.Weight: 10.5–12 oz. • Wing Loading: 6.6–7.5 oz. per ft

3 1200–1500 mAh LiPoly Cells @ 7 amps. • Total Input Watts: 77 or 110 watts per lb.

Unlimited Verticals, 20 minutes of Aerobatics or 50 minutes of Relaxed Sport Flying with Astro .010 & LiPoly 1500s

APC Slow-Flyer Prop: 10” x 7” @ 5,300 rpm • Top Speed: 32 mph • Thrust: 16 oz.

Recommended Motor: Astro Brushless .010 Geared (801G) • Prop 10"x7" APC Slow Flyer

Controller: Phoenix 10 w/BEC • Radio/Transmitter : 4 Channel • Receiver: FMA M5 • Servos: 3 Hitec HS55

ElectroFlying, Inc.

2547 83rd Court North, Minneapolis, MN 55444
763-560-5529 • [email protected]
© 2003, ElectroFlying, Inc. All Rights Reserved

Rev.#9 11/9/2006

eSKA INSTRUCTION MANUAL

Содержание eska





















Результаты поиска

Содержание eska

Отзывы:

Похожие инструкции для eska

Бренды по названию

Популярные бренды

ElectroFlying eska, Инструкция по эксплуатации

Результаты поиска

Содержание eska

Отзывы:

Похожие инструкции для eska

Бренды по названию

Популярные бренды