background image

Electro-Voice® ZxA1 Owner’s Manual

5

Tripod and Floor Monitor Operation

Floor Monitor

Electro-Voice ZxA1 loudspeakers may be used as a floor monitor by placing the speaker on the integral 
monitor angle.  Make sure to:

• Place the speaker on a level, stable surface that is solid and secure.
• Route cables and position the stand so that performers, production crew and audience members
will not trip over the stand or cables and pull the speaker system over. Secure cables with wire
ties or tape whenever possible.

Tripod

Electro-Voice ZxA1 speakers include 35mm (1-3/8 inch) stand mounts to allow mounting on tripod
stands.  Make sure to:

• Check the specifications of the speaker stand to be certain it is capable of supporting the weight of 
the speaker.
• Check that the speaker stand is placed on a flat, stable surface and be sure to fully extend the
legs of the stand. Do not try to make the stand “taller” and compromise its structural integrity.
• Route cables and position the stand so that performers, production crew and audience members
will not trip over the stand or cables and pull the speaker system over. Secure cables with wire
ties or tape whenever possible.
• Do not attempt to suspend more than one speaker on a stand designed for a single speaker
• Unless you are confident that you can safely handle lifting the weight of the speaker onto the
stand, ask another person to help you place it.
• Tighten the set screw to minimize rattling and to 
prevent the speaker from rotating during use.

Figure 1:

ZxA1 Monitor Position

Figure 2:

ZxA1 Pole Mount Location

Pole Mount Recess

Set Screw

Содержание ZxA1-100B













Отзывы: