Electro-Voice X-Line series Скачать руководство пользователя

Страница: 18 / 44

ELECTRO-VOICE

X-Line

Rigging Manual

ALWAYS CHECK TO MAKE SURE THAT THE PULL-UP-BAR HINGE BASES

ARE INSTALLED WITH THE CORRECT ORIENTATION WITH THE HINGES AT

THE OUTSIDE EDGES OF THE TRACK. ALWAYS CHECK TO MAKE SURE THE

PULL-UP-BAR HINGE BASES ARE SECURELY LOCKED INTO THE TRACK,

AND THAT THE LOCKING PINS ARE FULLY ENGAGED IN THE TRACK

BEFORE LIFTING ANY LOUDSPEAKER ENCLOSURES OVERHEAD. WHEN

PULLING BACK WITH A PULL-UP ASSEMBLY, ONLY USE ENOUGH FORCE TO

ELIMINATE THE SLACK FROM THE FRONT CHAINS. IF Xvhl LINKING HINGES

ARE USED TO SECURE THE TOP ENCLOSURE TO THE REAR OF THE GRID,

NEVER ALLOW THESE HINGES TO GO INTO COMPRESSION. IF Xvhg GRID

HINGES ARE USED TO SECURE THE TOP ENCLOSURE TO THE REAR OF

THE GRID, NEVER ALLOW THESE HINGES TO GO SLACK. IF FRONT AND

BACK HOIST MOTORS ARE USED TO SUSPEND THE GRID, NEVER ALLOW

THE REAR MOTOR TO GO SLACK.

1.6 ATM X-Line Grid Details

ATM Flyware manufactures the X-Line Grid, shown in Figure 7, specifically for the X-Line

loudspeaker systems. The grid is completely compatible with the X-Line systems. There is rigging

track on the front of the grid that matches the track on the front of the X-Line enclosures - with the

exception that there is only one attachment position on the grid instead of six as on the enclosure.

The Electro-Voice Xvsg front chain rigging straps are used to attach the front of the top enclosure

in a column to the grid.

Figure 7:

ATM Flyware X-Line Grid

Weight:

260 lbs (118 kg)

Note:

Grid Rigging track locations

are the same as the Xvls, Xvlt,

and Xsub Enclosures

53.000in

(1346mm)

15.182in
(386mm)

19.432in
(494mm)

48.614in

(1235mm)

49.239in

(1251mm)

2.062in

(52.4mm)

10.344in
(263mm)

5.719in

(145mm)

4.000in

(102mm)

3.000in (76.2mm)

TYP.

34.615in (879mm) MAX.

10.615in (270mm) MIN.

Содержание X-Line series













































Результаты поиска

Содержание X-Line series

Отзывы:

Похожие инструкции для X-Line series

Бренды по названию

Популярные бренды

Electro-Voice X-Line series, Руководство по монтажу

Результаты поиска

Содержание X-Line series

Отзывы:

Похожие инструкции для X-Line series

Бренды по названию

Популярные бренды