Xcn T
w
o
-W
ay MB/HF System
Xcn Two-Way MB/HF System
4
Xcn Two-Way, MB/HF System
can be replaced with the driver attached to
the horn.
MB: Remove the screws securing the
hatch on the back of the enclosure and lift
the hatch out. Remove the screws secur-
ing the 12-inch driver and lift the driver out
of the enclosure. In the event of failure,
the entire driver must be replaced.
The following service parts are available
from the service department in Buchanan,
Michigan USA:
HF:
#84423-XX 16-ohm ND5-16
diaphragm kit
#827-2973 ND5-16 complete driver
MB:
#812-2858 ND12A complete driver
LF:
#818-2883 EVX-180B complete driver
The complete drivers are available only for
repair replacement and are not available
for general sale.
Architects’ and Engineers’
Specifications
The loudspeaker system shall be a three-
way, active, coaxial, MB/HF system with a
frequency response from 125-20,000 Hz with
crossover frequencies at 125 and 1,760 Hz
and a rotatable 60° x 40° constant-directiv-
ity coverage pattern. The loudspeaker sys-
tem shall have a high-frequency compres-
sion driver mounted on a 60° x 40° constant-
directivity horn, and shall have a 16-ohm,
76.2-mm (3-in.) diameter voice coil, a
76.2-mm (3-in.) titanium dome, a 35.6-mm
(1.4-in.) exit, a neodymium magnetic motor
structure, and a 75-watt power rating.
The loudspeaker system also shall have
a 305-mm (12-in.) mid-bass driver
mounted on a mid-bass horn, and shall
have a 16-ohm, 63.5-mm (2.5-in.) diameter
voice coil, a neodymium magnetic motor
structure, and a 300-watt power rating. The
loudspeaker shall have a rigging system
enabling a column of loudspeakers to be
hinged at their back corners with relative
downward angles set by adjustable rigging
straps at the front. The enclosure shall be
constructed of 18-mm thick, 13-ply birch
plywood, and shall be trapezoidal forming
an 18° wedge, and be 596 mm (23.46 in.)
high, 584 mm (23.00 in.) wide at the front,
354 mm (13.93 in.) wide at the back and
759 mm (29.88 in.) deep and shall weigh
60.8 kg (134 lb). The loudspeaker sys-
tem shall be the Electro-Voice Xcn.
Rigging Accessories
Grid: This ATM Fly-Ware™ “T”-shaped,
all-steel-construction grid was specifically
designed as a single column of X-Array™
systems. Multiple grids can be linked to-
gether with couplers on front and back re-
tractable arms, the position of which sets
the splay angle between adjacent columns.
Part number MEGS-4000-T. ATM
Fly-ware™, 2100 S. Wilmington Ave.,
Carson, CA 90810 USA, 310/834-5914
Xrhg Grid Hinge: Two Xrhg grid rigging
hinges are used to attach the rear of the
top enclosure in a column to the rear of an
X-Array
™
compatible grid. Each hinge con-
sists of two precision-machined steel rig-
ging-track fittings connected by an alloy-
steel chain. Part number 510-2999. Electro-
Voice, 600 Cecil St., Buchanan, MI 49107
USA, 616/695-6831 or 800/234-6831
Xrhp Pickup Hinge: Two Xrhp pickup
rigging hinges are used to create custom
rigging assemblies to attach to the rear of
the top enclosure in a column when an
ATM grid is not used. Each hinge con-
sists of one precision-machined steel rig-
ging-track fitting with an alloy-steel chain.
Part number 510-3000. Electro-Voice, 600
Cecil St., Buchanan, MI 49107 USA,
616/695-6831 or 800/234-6831
Xrhl Linking Hinge: Two Xrhl linking
rigging hinges are used to link two enclo-
sures together at the rear. Each hinge con-
sists of two precision-machined steel rig-
ging-track fittings connected by a heavy-
duty steel hinge. Part number 510-2998.
Electro-Voice, 600 Cecil St., Buchanan, MI
49107 USA, 616/695-6831 or 800/234-6831
Xrsl Long Rigging Steel Straps: Two Xrsl
long rigging straps are used at the front of
two enclosures to adjust their relative ver-
tical angles. The Xrsl may also be used to
attach the front of the top enclosure to the
ATM grid when upward angles are not re-
quired. Each all-steel strap consists of two
New Haven NH32102-2 double-stud fit-
tings connected by black plastic-coated
wire rope. Sound Manufacturing Inc., 3336
Primera Ave., Hollywood, CA 90068 USA,
213/850-5042 or ATM Fly-ware™, 2100 S.
Wilmington Ave., Carson, CA 90810 USA,
310/834-5914
Xrss Short Rigging Steel Straps: Two
Xrss short rigging straps are used to at-
tach the front of the top enclosure to the
ATM grid. The Xrss may also be used at
the front of two enclosures when a limited
range of vertical angles are required. The
all-steel Xrss utilizes the same construc-
tion as the Xrsl. Sound Manufacturing Inc.,
3336 Primera Ave., Hollywood, CA 90068
USA, 213/850-5042 or ATM Fly-ware™,
2100 S. Wilmington Ave., Carson, CA 90810
USA, 310/834-5914
General Rigging Supplies: A wide vari-
ety of standard and specialty rigging hard-
ware components for both touring and per-
manent-installation applications is avail-
able. Sound Manufacturing Inc., 3336
Primera Ave., Hollywood, CA 90068 USA,
213/850-5042 or ATM Fly-ware™, 2100 S.
Wilmington Ave., Carson, CA 90810 USA,
310/834-5914
Electronic Accessories
Klark Teknik DN8000 Digital Control-
ler: The DN8000 digital electronic loud-
speaker controller has a two-in/five-out ar-
chitecture, with each output having pro-
grammable high-pass and low-pass filters,
four-band equalization, signal delay, com-
pressor- limiter-and noise-gate functions.
Program parameters for optimal perfor-
mance of the X-Array™ systems are avail-
able. Klark Teknik, Klark Industrial Park,
Walter Nash Road, Kidderminster,
Worcestershire DY11 7HJ England, 44-156-
274-1515
Electro-Voice Dx38 Digital Controller:
The Dx38 digital electronic loudspeaker
controller has a two-in/four-out architec-
ture, with each output having program-
mable high-pass and low-pass filters, four-
band equalization, signal delay compres-
sor and limiter functions. Program param-
eters for optimal performance of the
X-Array™ systems are available. Electro-
Voice, 600 Cecil St., Buchanan, MI 49107
USA, 616/695-6831
