Trans mit ter Dis play Squence:
Bat tery In di ca tor:
Battery condition is displayed on power up. The low battery
LED should flash once to indicate an ac ceptable bat tery. If the
battery is nearly depleated, the low bat tery LED will come on
and stay on. When bat tery voltage is too low for proper micro-
phone op eration, the low battery LED will flash continuously
and the unit will not transmit. You can check battery con dition
at any time by pressing the MENU but
ton twice from the
Group/Channel display screen. Battery con dition is also dis-
played at the re ceiver.
Group and Chan nel Set ting:
Transmitter fre quencies are di vided into 20 Groups of 16 fre -
quencies (or Channels). Fre quency Groups 1 through 10 are
predefined and cannot be changed. Frequency Groups 11u
through 20u can be set by the user.
To set the Group and Chan nel:
Press SET at the
Group/Channel display screen. When the Group number be -
gins to flash, use UP or DOWN to change the Group number.
Press SET to save the new Group setting. When the Chan nel
number be
gins to flash, use UP or DOWN to change the
Channel number. Press SET to save the new Channel setting.
Press MENU if you wish to stop without saving.
Dis playing and Set ting Trans mit ter Fre quency:
To see the current op erating frequency, press MENU at the
Group/Chan nel Screen.
Set ting Cus tom Fre quencies:
Select a Group be tween 11u
and 20u and a Chan nel between 1 and 16 (see
Group and
Chan nel Set ting
above). Press MENU to display the transmit-
ter fre
quency. If this Group/Channel is blank you will see
'---.---' on the frequency dis play. (Blank channels also dis play
a '-' af ter the channel number on the Group/Channel screen).
Press SET and use the UP or DOWN but tons to change the
frequency. Press SET to save the new fre quency, or MENU to
quit without saving changes since SET was last pressed.
Power Switch Disable:
When the Power Switch is disabled, you must move the power
switch to the OFF po
sition and then press a con
trol key
(MENU, SET, UP or DOWN) to power the unit off.
To en gage a one-time power switch lock: Turn the unit on. Af -
ter the display shows Group & Channel, quickly turn the
power off and on three times. "On-Loc" will show on the dis-
play. A One-time lock dis ables it self the next time the unit is
turned on.
To al ways lock the power switch ON, press and hold SET,
then press UP. "On-Loc" will show on the display.
To dis
able Power Lock, press and hold SET, then press
DOWN. "On-Off" will show on the dis play. The unit can now
be turned off with just the power switch.
Firm ware Re vi sion Level:
Hold down MENU for 5 seconds. The pro gram firmware revi-
sion number will dis play, fol lowed by the factory pre set fre -
quency group re vision number.
Quick Setup:
Press and hold the MENU but ton. Turn on the power switch.
Wait un
til Group and Chan
nel are displayed. Release the
MENU button. Unit is now set to Group 1/Channel 1 with
Group or Channel Flashing.
Fac tory Re set:
WARNING: This will erase any user frequencies stored in
Groups 11u to 20u.
From the Group/Channel screen, press
and hold MENU, SET, UP and DOWN until "Clr.All" is dis-
played on the LCD screen. Unit will restart in Quick Setup
mode.
3-8
Battery Gauge:
Display 3 seconds
Group Channel
Press MENU
Frequency Display
Press MENU
Battery Gauge
Press MENU
Содержание Telex RE-1
