background image

Electro-Voice

®

 

 Sx600 User Manual

Product Description

The Sx600 Series is a remarkably flexible indoor/outdoor speaker

system designed to produce high-fidelity high-level audio in distributed

applications such as stadiums, racetracks, amusement parks,

fairgrounds, etc.  Utilizing a 65° x 65° high frequency horn and a unique

2-element vertical midbass array, Sx600 gives you the clarity of a direct

radiator with the high SPL and directivity of a properly designed horn

system, especially in the important vertical plane.  While intended

primarily for vocal applications, the Sx600 accurately reproduces music if

heavy bass is not required.

Important Features

The Sx600 is available as either a conventional 4 ohm low impedance

system, the Sx600PI, or as a “constant voltage” system, the Sx600PIX.

The PIX version features a 100% duty cycle rated 600 watt full isolation

line transformer for operation with 70volt, 100volt, 140volt, or 200volt

distributed systems.

The Sx600 comes with an all-new Super Strong Arm Mount, called the

SuperSAM

TM

.  This exclusive 2-part EV mounting system allows the

installer to pre-set the exact down angle on the ground, fasten the

separate mounting bracket by itself, and then mount the speaker to the

bracket quickly and easily with a single bolt, setting the pan angle

anywhere within a 180° arc in the process.

The three-layer stainless steel grill design is an acoustically transparent

yet effective barrier to both condensation and heavy rain. The light-

weight polypropylene enclosure has strategically placed internal

passages to conduct moisture that may accumulate internally out to the

side channels where it drains away.

1

Содержание SX Series SX600

















Отзывы: