This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation. If the device is not installed and used in accordance with
the instructions, it may cause harmful interference to radio communications and void
the user's authority to guarantee the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the user's
authority to operate the equipment under FCC rules.
H.O.G.2 FOOT CONTROLLER
Preset Controller for HOG2
Congratulations on your purchase of the Electro Harmonix
HOG2 FOOT
CONTROLLER
! When connected to your HOG2 main unit, the Foot Controller gives
you access to 100 presets, allowing you to load and save your favorite HOG2
settings. Every slider position and mode selection is stored when you save a preset
and faithfully recalled when you load the preset at a later date. If an expression pedal
is connected to the HOG2 it will even store its position at the time of saving.
- GETTING STARTED -
Connect the HOG2 Foot Controller (HOG2 FC) to your HOG2 main unit using a
standard 1/4” mono instrument cable. Plug into the jack labeled FOOT CONTROLLER
on the HOG2. The other end of the cable should be inserted into the HOG2 FC’s jack
labeled INPUT. As long as the HOG2 main unit is powered up, the digits on the HOG2
FC will light up indicating it is ready for use.
- DISPLAY AND CONTROLS -
2-DIGIT LED DISPLAY
– The LEDs display the currently selected or loaded preset
number. The numbers range from 0 to 99. When a preset is loaded, the rightmost
decimal point on the HOG2 FC and PRESET LED on the HOG2 main unit will light
indicating a PRESET is active. If the rightmost decimal point is not lit, then either no
PRESET is currently loaded or the HOG2 is in bypass mode.
UP/DOWN Footswitches
– If no preset is currently loaded, pressing either
footswitch will load the preset associated with the currently displayed number. For
example, if the HOG2 FC is displaying 0 and the decimal point next to 0 is not lit,
pressing either footswitch will load Preset 0.
If a preset is loaded, press and release the UP Footswitch and the digits on the HOG2
FC will increment by one while simultaneously loading the preset indicated by the
new number. For example, if your HOG2 FC is displaying 0 and you press the UP
Footswitch, the display will load and show Preset 1. The DOWN footswitch does the
same but instead decrements by one.
Press and hold either footswitch for approximately half a second to jump up or down
by ten presets instead of just one.
SELECT Knob
– The SELECT knob can be used to scroll through the presets without
loading a new preset. Turn the knob clockwise to scroll up through the presets, turn
the knob counter-clockwise to scroll down. Press and release the SELECT knob to
load the currently displayed preset. If a preset is loaded, and you turn the SELECT
knob, the numbers will blink indicating that a different preset is actually loaded.
