manualshive.com logo in svg

electrifly PBY CATALINA, Инструкция по эксплуатации

Поделиться
Скачать
electrifly PBY CATALINA Скачать руководство пользователя страница 14

14

FINAL ASSEMBLY

Complete the Radio Installation

❏

 1. Plug the elevator and rudder servo into the appropriate 

channels in the receiver. Plug the motor wires into the speed 
control and plug the ailerons into the “Y” connector. Plug 
the aileron “Y” connector and the speed control into the 
appropriate channels in the receiver.

FULL THROTTLE

RUDDER MOVES RIGHT

ELEVATOR MOVES UP

RIGHT AILERON MOVES UP

LEFT AILERON MOVES DOWN

4-CHANNEL RADIO SETUP

(STANDARD MODE 2)

❏

 2. Place the fl ight battery into the battery tray. Turn on the 

transmitter and then plug the fl ight battery into the speed 
controls. 

Do not arm the motors!

 WIth the radio on and all 

control surfaces functioning, make certain that the control 
surfaces and the throttle respond in the correct direction as 
shown in the diagram. If any of the controls respond in the 
wrong direction, use the servo reversing in the transmitter 
to reverse the servos connected to those controls. Be 
certain the control surfaces have remained centered. Adjust 
if necessary. You should make any adjustments to the 
servos and the servo arms 

now

. In a future step you will 

be installing the blisters over the openings in the fuselage, 
making adjustments to the servos diffi cult.

❏

 3. Make all of the connections for the ailerons and the 

motors. Then mount the wing to the fuselage. Make any 
adjustment required to the aileron and double check to be 
sure the motors are running the correct direction. Disconnect 
the battery and turn off the transmitter.

Finishing Touches

❏

 1. Locate the fuselage plug and insert it into the hole in 

back of the step of the fuselage. After each fl ight it is a good 
idea to remove the plug and drain any water that may have 
gotten into the fuselage.

❏

 2. On both sides of the fuselage are mold dimples. On each 

of the dimples drill a 1/16" [1.6mm] hole through the fuselage.

❏

 3. Install a strut into each of the holes with a 2 x 10mm 

[3/8"] washer head screw. When installing the screw do not 
push too hard against the fuselage causing it to buckle. If 
necessary support the fuselage by putting one hand inside 
of the fuselage for support.

Содержание PBY CATALINA





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды