Electra Gcz 12, Руководство по обслуживанию

Страница: 174 / 205

1. M a r k the loc a tion o f the hole on either side o f the m ountin g pl a te a s
sho w n. a nd drill it a t a 5 do w n wa rd a n g le, a s sho w n.
2 . The hole is drilled a t a n a n g le, to prevent condensed or r a in wa ter
f ro m penetr a tin g b a c k into the roo m
3. Tri m the hole in the wa ll w ith a 7 0 mm co mm erci a l pl a stic tube.
PENETRATION OF WALL FOR TUBING
Fig. 10
A.OUTDOOR SIDE 1.Drill 70 mm
B.INDOOR SIDE
2.Wall
1. M ak e sure th a t the re f ri g er a nt tubes, electric c a bles a nd condens a te
wa ter hose a re w ell insul a ted w ith closed cell rubber b a sed insul a tin g
tubes( 6 mm thic k ness), a re w r a pped to g ether w ith U V st a bili z ed non-
a dhesive pl a stic t a pe, a nd a re p a ssed throu g h the hole in the wa ll.
2 . H a n g the indoor unit on the t w o hoo k s th a t a re loc a ted ne a r the top
ed g e o f the m ountin g pl a te.
3. Press the lo w er p a rt o f the indoor unit aga inst the m ountin g pl a te
until the c a tches sn a p into the slots a nd loc k the indoor unit to the
m outin g pl a te.
4. Chec k the inst a ll a tion by pullin g the unit to wa rds you.
5. To rele a se the unit f ro m the m ountin g pl a te, li f t up the unit a nd then
pull the unit to wa rds you, to ensure th a t the hoo k s a re loc k ed.
S U S PENDING A ND RELE AS ING THE UNIT FROM THE
MOUNTING PL A TE
Fig.11
1.Indoor unit 3.Top hooks
2.Snap catches 4.Botoon hooks
Fig.12
1.Mounting plate
3.Lift up
2.Lower hook 4.Pull
CONDENSATE HOSE
CONNECTION
1. A tt a ch the condens a te dr a in hose to the corru ga ted hose in the
re a r g roove o f the indoor unit.
2 . Wr a p the dr a in hose
to g ether w ith the
re f ri g er a nt tubes a nd
electric a l c a bles.
3. Ensure th a t the
condens a te dr a in
hose is a t a ll points
inst a lled in a
do w n wa rd slope
ma nner.
4. When inst a llin g the
dr a in hose a voide
tr a ps a nd U-bends.
The end o f the dr a in
hose should not be
i
mm ersed in wa ter.
5. For a le f th a nd outlet,
l a y the dr a in hose on
the botto m o f the
indoor unit re a r
g roove.
6 . When the inst a ll a tion
loc a tion re q uires lon g
hori z ont a l sections, a
vent m ust be provided
a t the top o f the hose
to prevent over f lo w o f
the unit dr a in p a n.
Upon co m pletin g the inst a ll a tion, test the wa ter dr a in by pourin g
a t le a st t w o liters o f wa ter into the unit dr a inp a n. Chec k th a t the
wa ter dr a ins o ff .
Fig.13
1.drain hose
2.Clamp
3.Downward slope
Fig.16
1.Vent
2.Downword drain
3.Water drain hose
Fig.15
1.Electric calbe
2.Refrigerant tubing
3.Condensate drain hose
Fig.14
1.Trap
2.U-bend
3.End immersed in water
5
Fi g 3 1
1
2
3
Fi g 14
1 3 2
1
2
3
Fi g 5 1
Fi g 6 1
1
2 3
1
2
3
4
Fi g 1 2
1 2 3
4
Fi g 11
Fi g 10
A
B
1
2
5