Electra e3 Скачать руководство пользователя страница 11

11 

      e

FLUSH MOUNT 

OCCUPANCY DETECTOR

INTRODUCTION

e3  is  a  360  degree  flush  mount  occupancy 
detector  that  uses  a  passive  infrared  sensor 
to  detect  changes  in  temperature  emitted  by 
persons  or  objects  passing  through  its 
detecting area. 
The  sensor  will  keep  the  connected  lighting 
fixture on even when you are seated and can 
detect  very  slight  movements  (a  seated 
person’s head or hand movements). 

e3  can  support  “master/slave”  connections 
for large area coverage requirements. 

Note:  Read  this  entire  manual  before  you 
start to install the system. 

PRODUCT OVERVIEW

 Lens 

 Main Body 

 Protection Case 

 Spring Clip (x2) 

SAFETY PRECAUTIONS

  Avoid  installing  the  unit  in  storming  or 

raining weather. 

  Be  sure  to  isolate  or  switch  off  power 

source before installing or maintenance. 

  DO ensure that the power supply circuit is 

protected  by  a  16  amp  circuit  breaker  or 
suitable equivalent fuse. 

IMPORTANT 

Installation must be performed by skilled technicians 
who are informed about the standards and technical 
requirements  of  the  appliance  and  its  proper 
installation. 

Check  your  local  codes  as  they  apply  to  your 
situation.    If  the  house  wiring  is  of  aluminum, 
consult  with  an  electrician  about  proper  wiring 
methods. 

Before proceeding with the installation, TURN OFF 
THE POWER TO THE LIGHTING CIRCUIT AT   
THE CIRCUIT BREAKER OR FUSE BOX TO   
AVOID ELECTRICAL SHOCK.

CHOOSING A MOUNTING LOCATION

When deciding a proper location to install the 
unit,  please  take  the  following  points  into 
consideration: 

  The unit is designed for indoor ceiling 

flush mount and is not suitable for wall 
mount. (FIGURE 1) 

FIGURE 1 

  Avoid  aiming  the  occupancy  detector  at 

pools,  heating  vents,  air  conditioners  or 
objects  which  may  change  temperature 
rapidly. 

  Do not allow sunlight to fall directly on the 

front of the unit. 

  The occupancy detector is more sensitive 

to an object moving across its field of view.   
It  is  less  sensitive  to  an  object  moving 
directly 

towards 

the 

sensor 

head. 

(FIGURE 2) 

FIGURE 2 

  The unit has a sensing angle of 360° and 

can detect up to 3 meters radius for micro 

Содержание e3

















Отзывы: