Elecro Engineering Cygnet Evolution 2 Скачать руководство пользователя страница 15

15 

 

 

Heater is tripping circuit breaker (MCB) after few minutes/ hours of operation: 

 

If the heater is faulty it will instantly trip the circuit breaker (MCB). The most likely causes of tripping 
the breaker after a period of time are: 

 

Possible Cause 1:  

Faulty circuit breaker. 

Possible Cause 2: 

Incorrect size of the

 

circuit breaker. 

Possible Cause 3:  

Cross section of the cable is not sufficient. 

Possible Cause 4:  

Loose connection(s) of the power supply cable. Check both ends of 
the  power  supply  cable  (at  the  distribution  box  and  at  the  heater 
terminal block). 

 

Remedy: 

Contact an Electrician to check installation and protection. 

 

 

Heater is tripping circuit breaker (MCB) or RCD instantly: 

 

Possible Cause 1:  

Short circuit caused by the wiring or faulty components. 

Possible Cause 2: 

Heating element is going to ground or is damaged. 

Possible Cause 3:  

Moisture inside the heater. 

 

Remedy: 

Send heater back to the manufacturer. Use return form on page 17 
or download it from the Elecro website. 

 

 

Power supply cable is getting very hot: 

 

Possible Cause 1:  

Cross section of the power supply cable is not sufficient. 

Possible Cause 2:  

Loose connection(s) of the power supply cable. Check both ends of 
the  power  supply  cable  (at  the  distribution  box  and  at  the  heater 
terminal block). 

 

Remedy: 

Contact  an  Electrician  to  check  installation.  Inspect  for  loose 
connections and upgrade the power supply cable to a bigger size if 
necessary. 

5.  MAINTENANCE 

 
We recommend annual maintenance and cleaning of the heater to ensure proper operation. 

 

WARNING:

   Before performing any maintenance on the unit isolate from the main power supply. 

 
The  heater  should  be  drained,  the  flow  tube  and  heating  elements  should  be  cleaned.  Removing 
scale/sludge and any debris or blockages will extend life expectancy of the heating element(s) and avoid 
potential failures. 
 
Check that electrical cable connections are properly tightened. 

6. DISPOSAL OF ELECTRICAL/ELECTRONIC EQUIPMENT 

 

DO NOT dispose of this product as an unsorted municipal waste. 

 

This  symbol  on  the  product  or  on  the  packaging  indicates  that  this  product  should  not  be  treated  as 
household waste.  Instead it should be handed over to the applicable collection point for the recycling of 
electrical and electronic equipment. 
 

 

By ensuring this product is disposed of correctly you will help prevent potential 
negative  consequences  for  the  environment  and  human  health,  which  could 
otherwise  be  caused  by  inappropriate  waste  handling  of  this  product.    The 
recycling of materials will help to conserve natural resources. 
 
For  more  information  please  contact  your  local  Civic  Office,  household  waste 
disposal service or the retailer where the product was purchased. 

Содержание Cygnet Evolution 2





















Отзывы: