MANUAL ELDES ESIM264 V3.2
MANUAL ELDES ESIM264 V3.2
EKB3
Enter parameter 21 and parameter status value:
21 1 #
Example:
211#
Config
Tool
This operation may be carried out from the PC using the
ELDES Configuration Tool
software.
Disable SMS text
message to all listed
user phone numbers in
case of alarm
SMS
SMS text message content:
ssss_SMSALL:OFF
Value:
ssss
– 4-digit SMS password
Example:
1111_SMSALL:OFF
EKB2
Menu path:
OK
→
CONFIGURATION
→
OK
→
aaaa
→
OK
→
PRIMARY SETTINGS
→
OK
→
CALL/SMS
SETTINGS
→
OK
→
SEND ALARM SMS ALL
→
OK
→
DISABLE
→
OK
Value:
aaaa
– 4-digit administrator password.
EKB3
Enter parameter 21 and parameter status value:
21 0 #
Example:
210#
Config
Tool
This operation may be carried out from the PC using the
ELDES Configuration Tool
software.
By default, tamper alarm notification by SMS text message is enabled. For more details on how to disable/enable tamper alarm notification,
please refer to
16. TAMPERS
.
ATTENTION:
Regardless of the Call in Case of Alarm parameter status, the system will NOT ring the listed user phone number if the system
is connected to the monitoring station (see
30. MONITORING STATION
).
18. PROGRAMMABLE (PGM) OUTPUTS
A PGM output is a programmable output that toggles to its set up state when a specific event has occurred in the system, the scheduled
weekday and time has come or if the user has initiated the PGM output state change manually. Normally, PGM outputs can be used to open/
close garage doors, activate lights, heating, watering and much more. When a PGM output turns ON, the system triggers any device or relay
connected to it.
ESIM264 comes equipped with four open-collector PGM outputs allowing to connect up to four devices or relays. For more details on PGM
output expanding, please refer to
18.2. PGM Output Expansion
.
ESIM264 PGM outputs are classified by 4 categories:
PGM output category
Description
Max. number of PGM
outputs per device
Max. number of PGM
outputs in total
On-board PGM Outputs
Built-in wired PGM outputs of ESIM264 alarm system.
4
4
EPGM8 PGM Outputs
PGM outputs of EPGM8 - hardwired PGM output expan-
sion module.
8
8
EPGM1 PGM Outputs
PGM outputs of EPGM1 - hardwired zone and PGM output
expansion module.
2
4
Wireless PGM Outputs
Non-physical PGM outputs automatically created by con-
nected wireless devices.
2*
32**
* - Depends on the connected wireless device.
** - Available only if no EPGM1 PGM outputs are present.
For PGM output wiring diagram, please refer to
2.3.6. Relay Finder® 40.61.9.12 with Terminal Socket 95.85.3
.
18.1. PGM Output Numbering
The PGM output numbers ranging from C1 through C12 are permanently reserved for on-board PGM outputs even if EPGM8 module mode is
disabled. The C13-C44 PGM output number are automatically assigned in the chronological order to the devices connected to the system:
EPGM1 modules and wireless devices.
18.2. PGM Output Expansion
For additional electrical appliance connection, the number of PGM outputs can be expanded by:
• connecting EPGM8 hardwired PGM output expansion module. (see
18.2.1. EPGM8 Mode
and
31.3.1. EPGM8 – Hardwired PGM
Output Expansion Module
)
• connecting EPGM1 hardwired zone and PGM output expansion module (see
31.1.3. EPGM1 – Hardwired Zone and PGM Output
Ex pansion Module
).
• pairing the wireless devices (see
19. WIRELESS DEVICES
).
The maximum supported PGM output number is 76.
18.2.1. EPGM8 Mode
EPGM8 is an expansion module, which expands the system with 8 additional hardwired PGM outputs. For more details on EPGM8 module
installation, please refer to
31.3.1. EPGM8 – Hardwired PGM Output Expansion Module.
Once the EPGM8 module is installed, the EPGM8 mode must be enabled.
Enable EPGM8 mode
EKB2
Menu path:
OK
→
CONFIGURATION
→
OK
→
aaaa
→
OK
→
PGM OUTPUTS
→
OK
→
USING EPGM8
→
OK
→
ENABLE
→
OK
Value:
aaaa
– 4-digit administrator password.
EKB3
Enter parameter 33 and parameter status value:
33 1 #
Example:
331#
Config
Tool
This operation may be carried out from the PC using the
ELDES Configuration Tool
software.
Содержание ESIM264
Страница 60: ...MadeintheEuropeanUnion www eldes lt...