Eldes ESIM264, Руководство по установке

Страница: 13 / 60

24 25 24 25 EN EN MANUAL ELDES ESIM264 V3.2 MANUAL ELDES ESIM264 V3.2
5.4. ELDES Configuration Tool Software
Config
Tool
Software ELDES Configuration Tool is intended for ESIM264 alarm system configuration via USB port locally or via GPRS con-
nection remotely. This software simplifies system configuration process by allowing to use a personal computer in the process.
Before starting to use ELDES Configuration Tool software, please read the user guide provided in the software’s HELP section.
ELDES Configuration Tool is freeware and can be downloaded from at: www.eldes.lt
5.4.1. Remote Connection
ATTENTION: The system will NOT send any data to monitoring station while configuring the system remotely via GPRS network. However,
during the configuration session, the data messages are queued up and transmitted to the monitoring station after the configuration session
is over.
ATTENTION: When the Configuration mode is activated by EKB3 keypad or menu section CONFIGURATION is opened by EKB2 keypad, re-
mote system configuration will be disabled.
NOTE: The keypads will be inactive when the system is being configured remotely.
ELDES Configuration Tool software provides remote system configuration ability via Internet using one of the following methods:
• ELDES proxy server (recommended). The connection can be established on the system via GPRS network.
• Running TCP/IP server on
ELDES Configuration Tool (advanced). The connection can be established on the system via GPRS network.
In order to start using the remote configuration feature, please run the step-by-step wizard and follow the steps provided in the start page
of ELDES Configuration Tool software. Please, note that it will be necessary to send an SMS text message to the system’s phone number
in order to initiate the remote connection. By following the steps you will be instructed on what text must be sent to the system’s phone
number in such case.
5.4.2. Ending the Remote Connection Session
Terminate the
connection
with server
After the system configuration is complete, use one of the following methods to end the configuration
process:
• Click Disconnect or Stop button and close ELDES Configuration Tool software.
• The session will automatically expire in 20 minutes. Before the last 5 minutes, the software will offer
the user to extend the session for another 20 minutes.
• Alternatively, the connection with the server can be terminated at any time by sending an SMS text
message.
SMS
SMS text message content:
ssss_ENDCONFIG
Value: ssss – 4-digit SMS password.
Example: 1111_ENDCONFIG
Once the session is expired or terminated, the system will reply with an SMS text message confirming the end of the session.
6. PASSWORDS
For security reasons, the system uses the following types of passwords:
• SMS password – 4-digit password used for system arming/disarming and configuration by SMS text messages. By default, SMS pass-
word is 0000, which MUST be changed!
• Administrator password – 4-digit password used for Configuration mode activation by keypad and logging in to ELDES Configuration
Tool software. By default, Administrator password is 1470, which is highly recommended to change.
Set SMS password
SMS
SMS text message content:
wwww_PSW_ssss
Value: wwww – 4-digit default SMS password; ssss – 4-digit new SMS password; range –
[0001... 9999].
Example: 0000_PSW_1111
EKB2
Menu path:
OK → CONFIGURATION → OK → aaaa → OK → PRIMARY SETTINGS → OK → PASSWORDS
→
OK
→
SMS PASSWORD
→
OK
→
ssss
→
OK
Value: aaaa – 4-digit administrator password; ssss – 4-digit new SMS password; range –
[0001... 9999].
EKB3
Enter parameter 14 and new SMS password:
14 ssss #
Value: ssss – 4-digit new SMS password; range – [0001... 9999].
Example: 141111#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.
Set Administrator
password
EKB2
Menu path:
OK
→
CONFIGURATION
→
OK
→
1470
→
OK
→
PRIMARY SETTINGS
→
OK
→
PASSWORDS
→
OK
→
ADMIN PASSWORD
→
OK
→
aaaa
→
OK
Value: aaaa – 4-digit new administrator password; range – [0000... 9999].
EKB3
Enter parameter 16 and new administrator password:
16 aaaa #
Value: aaaa – 4-digit new administrator password; range – [0000... 9999].
Example: 162538#
Config
Tool
This operation may be carried out from the PC using the ELDES Configuration Tool software.