WSD01 Configurator
Installation
1. Insert the “Easywave DALI Gateway” CD into your CD
drive.
2. Execute the program “WSD01_Setup.exe” in the root
directory and follow the instructions during installation.
3. Launch the “WSD10 Configurator”.
The installation files can also be downloaded from our
website:
http://www.eldat.de/schnittstellen/wsd01e_de.html
Configuring the language
You can use the menu item “Language” to switch between
English and German at any time.
The language set in the operating system is used by default.
Establishing a connection with the WSD01
1. Connect the PC/laptop using the set-up cable to the
WSD01. The WSD01 must remain connected to the
DALI bus and must remain powered for the entire con-
figuration process!
2. Click on the “Connect” button in the “WSD01 Configu-
rator”. A green tick must appear after “USB Dongle” and
“DALI Wall-Mounted Button Unit”! If these ticks are not
present, restart the program.
The configuration of the currently connected WSD01 is im-
ported automatically upon connection.
Configuring the DALI functions
In the top area of the program window, it is first established
whether the WSD01 is being used with one button or two
buttons. This setting is dependent on the number of switches
mounted on the button unit (one or two).
If "1 switch" is selected, only the left area will be available for
DALI configuration. If "2 switches" has been selected, both
the left and right area will be available.
A dedicated combination of mode and DALI address for the
DALI devices to be controlled can then be configured for
each button position of the wall-mounted button unit. The
button positions of the wall-mounted button unit can be al-
located to the individual areas as follows:
Switch 1 - A: Top left
Switch 1 - B: Bottom left
Switch 2 - A: Top right
Switch 2 - B: Bottom right
In the current configuration, unusable button positions are
greyed out.
If a mode with two-button operation is selected, the corre-
sponding button positions will be allocated automatically and
the relevant area will be greyed out.
With one-button operation modes on the other hand, it is
possible to configure a dedicated function to each button
position.
Once you have created the desired configuration, click on
“Transfer” to transfer the data to the WSD01 wall-mounted
button unit.
If there are changes that have not yet been transferred, this
will be indicated at the bottom left with "Changes made".
In this case, the configuration should be transferred again.
The message "Transfer data" will appear at the bottom
left.
The configuration process is now complete and you can dis-
connect the USB cable from the gateway. The WSD01 is
ready for operation.
UM160422 0917 D
Available modes
DIM two-button operation
This mode enables the brightness of DALI devices to be
dimmed or increased.
A short press of the button switches the supplied devices on
to 100% (top) or switches them off to 0% (bottom).
Holding down the button will dim or brighten the supplied
devices.
ON/OFF two-button operation
The controlled DALI devices are switched as desired to ON
(top) or OFF (bottom).
DIM one-button operation
The controlled DALI devices are alternately dimmed or
brightened using the very same button position.
A short press of the button switches the supplied devices ON
to 100% or switches them OFF to 0%.
Holding down the button will alternately dim or brighten the
supplied devices.
ON/OFF one-button operation
The DALI devices are alternately switched ON or OFF using
the very same button position.
Open SCENE (one-button operation)
A scene that is stored in the DALI device is triggered. The
desired scene (0–15) must be set in the drop-down menu
“Scene”.
SKIP through scenes (one-button operation)
Each press of the button skips ahead by one scene within a
pre-defined scene range.
This range is set in the drop-down menu “Scene” and gener-
ally begins with Scene 0, ending at a maximum of Scene 15.
DEAD MAN'S SWITCH one-button operation
The controlled DALI devices are switched on as long as the
button is held down.
Fixed dim setting (one-button operation)
A fixed dim setting specified as a percentage is transferred to
the addressed DALI devices. This setting can be configured
in increments of 1% to any value between 0% and 100%
using the sliders.
Addressing
When using a mode with one-button operation, each of the
two button positions of a switch (top and bottom) can trigger
a separate DALI address.
If a mode with two-button operation is being used, each
switch can only trigger one DALI address. In this case, the
bottom button positions are allocated automatically, which
is why modes with two-button operation cannot be selected
here.
It is possible to control either ALL devices (broadcast), indi-
vidual devices or groups of devices.
To do this, select the relevant item in the “Devices” section,
then select the desired address in the corresponding drop-
down menu.
Individual devices can be controlled in the address range
0–63.
Groups can be controlled in the range 0–15.
Saving and loading the configuration
You can use the menu item “File” to save the current con-
figuration on the PC or laptop or import a previously saved
configuration into the “WSD01 Configurator”.
Please note that a loaded configuration must first be trans-
ferred to the wall-mounted button unit by clicking on “Trans-
fer” before it becomes active.
