GB
Multi Channel Transmitter RT22
74573 0805 GB
Duplicate
1. Connect both Multi Channel Transmit-
ters using the programming cable.
2. Hold down the level III button on the
target transmitter until LED III flashes.
3. Hold down the level IV button on the
source transmitter until LED IV flashes.
4. On both the target transmitter and the
source transmitter, press channel button
12 and hold down. The LED III on the
target transmitter flashes quickly, while
the LED IV on the source transmitter
flashes slowly. When both LEDs go off,
the duplication function is complete. Re-
lease both buttons.
Aborting the random coding process
•
Press the button 11 or the button 13.
Random Coding
1. Insert the programming cable into the
socket on the Multi Channel Transmit-
ter, and at the other end of the cable
short-circuit one of the outer pins with
the middle pin.
2. Select the required level using the level
buttons.
3. Press one of the channel buttons and
hold it down. The LED for that level will
flash quickly.
When the LED is continuously lit, this
indicates that a new code has been as-
signed at random. Release the button.
Note: After the channel button has been
released, the selected level remains acti-
vated for a further 10 seconds for the re-
coding of further channel buttons. The
transmitter then automatically switches to
Level I.
Caution!
The new coding must be transferred to the
radio control.
Replacing Batteries
1. Unscrew the battery housing cover.
2. Remove the old batteries.
3. Insert two new 3 V batteries. Use only
batteries of type CR2032.
Make sure the polarity is correct!
4. Screw the battery housing cover back
on.
Caution!
Keep batteries out of reach of children!
Troubleshooting
•
The LEDs are only faint when lit up:
Change the batteries.
•
The LEDs do not light up at all:
Check the polarity of the batteries.
•
Move closer to the radio control or
teach-in the Multi Channel Transmitter
channels to the radio control(s) again.
Cleaning
Wipe the housing carefully with a damp lint-
free cloth.
Caution!
Do not use solvent-based cleaning agents.
These can damage your health and destroy
the surface of the housing.
General Information
Disposal
Waste electrical products and batteries
should not be disposed of with house-
hold waste!
Dispose of the waste product via a
collection point for electronic scrap
or via your specialist dealer.
Dispose of used batteries in a
recycling bin for batteries or via the
specialist trade.
Put the packaging material into the
recycling bins for cardboard, paper
and plastics.
Warranty
Within the statutory warranty period we
undertake to rectify free of charge by repair
or replacement any product defects arising
from material or production faults.
Any unauthorized tampering with, or modifi-
cations to, the product shall render this
warranty null and void.
Conformity
This product conforms to the basic
requirements of the R&TTE Direc-
tive 1999/5/EC.
For use in: EU/CH/FL/N/IS
The Declaration of Conformity can be found
on the Internet at: www.eldat.de.
Technical Details
Frequency:
433.92 or 868.30 MHz
(depending on model)
Power supply:
2 x 3V batteries, CR2032
Indicator:
LED
Current consumption: approx. 15 mA
Degree of Protection: IP 54
Operating temperature: -20°C to +60°C
Range:
under favourable open
field conditions:
approx. 100 m
in buildings: approx. 30 m
Dimensions:
150 x 60 x 22 mm
Weight:
approx. 100 g
Customer Service
If, despite correct handling, faults or mal-
functions occur or if the product was dam-
aged, please contact the company at the
address below:
ELDAT GmbH
Im Gewerbepark 14
D-15711 Zeesen
Germany
Phone: + 49 (0) 33 75 / 90 37-0
Fax: + 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
e-Mail: [email protected]
