02-42/2015 Rev.3
RFDAC-71B
Analog controller
EN
1-10 V
Made in Czech Republic
PROG
<
3s
1 x
2/8
RF
RP
-2
0
Radio frequency signal penetration through various construction materials /
60 - 90 %
80 - 95 %
20 - 60 %
0 - 10 %
80- 90 %
brick walls
wooden structures
with plaster boards
reinforced
concrete
metal partitions
common glass
Indication, manual control /
button /
LED
• LED STATUS - indication of the device status.
Indicators of memory function:
On - LED blinks x 3.
Off - The LED lights up once for a long time.
• Manual control is performed by pressing the PROG button for
<
1s.
• Programming is performed by pressing the PROG button for 3 - 5s.
In the programming and operating mode, the LED on the component
lights up at the same time each time the button is pressed - this
indicates the incoming command.
Selecting the output voltage mode /
Selecting the output voltage mode 0-10V or 1-10V is performed by pressing the
Prog button for 1 - 3s.
After releasing the button, the LED flashes, indicating the output mode:
the green LED - 0-10V,
the red LED - 1-10V.
All other signalling is indicated by the relevant colour LED.
For more information, see “Installation manual iNELS RF Control”:
http://www.elkoep.com/catalogs-and-brochures
Compatibility /
The device can be combined with all system components, controls and devices
of iNELS RF Control and iNELS RF Control
2
.
The detector can be assigned an iNELS RF Control
2
(RFIO
2
) communication pro-
tocol.
Analogni kontroler 0(1)-10V
RS
U-Energister, d.o.o.| Noveških interniraca 1V | 31000 Užice | Serbia | e-mail: [email protected]
U-Energister, d.o.o. | Norveških interniraca 1V | 31000 Užice | Republika Srbija | e-mail: [email protected]
EN
Support: +381 63 479 880 |
RS
Tehnička podrška +381 63 479 880
www.elkoep.rs
Prenos radio frekvencijskih signala preko različitih građevinskih materijala
zid od
cigle
drvena konstuk-
cija sa gipsanim
pločama
armirani beton
metalne pre-
grade
staklo
Inikacije, ručna kontrola
taster PROG
• LED STATUS - indikacija stanja uređaja.
Indikacija funkcije memorije:
uključeno - LED 3x treperi.
isključeno - LED 1x svetlo duže.
• Ručni rad se vrši pritikom na taster PROG
<
1s.
• Programiranje se vrši pritiskom na taster PROG na 3 - 5s.
U režimu programiranja i pisanja, svaki put kada se pritisken taster
na kontroleru, LED na elementu počinje da dugo svetli- to označava
da je komanda primljena.
Odabir režima izlazne voltaže
Režim izlaznog napona 0-10V ili 1-10V se bira pritiskom an taster PROG tokom
1-3s.
Kada se otpusti tatser, LED treperi, signalizirajuci izlazni režim:
zelena LED - 0-10V
crvena LED - 1-10V
SVa ostala signalizacija je označena odgovarajućom LED bojom.
Za više informacija, pogledati ,,Instalaciono uputstvo iNELS RF kontrole":
https://www.elkoep.cz/preuzimanja
Kompatibilnost
Element se može kombinovati sa svim sistemskim elementima, kontrolerila
i elementima sistema iNELS RF Control i iNELS RF Control
2
.
Detektori obeleženi iNELS RF Control
2
(RFIO
2
) uz pomoć komunikacijskog
protokola takođe se mogu dodeliti elementu.
