background image

 

 
FCC NOTES (914,5MHz US version): 
 
NOTE: 
This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a commercial environment. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instruction manual, may cause harmful interference to radio communication. 
Operation of this equipment in a residential area is likely to cause harmful interference in which case 
the user will be required to correct the interference at his own expense. 
 
NOTE: 
This device complies with part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation. 
 
In order to maintain compliance with FCC regulation shielded cables must be used with this 
equipment. Operation with non-approved equipment or unshielded cables is likely to result in 
interference to radio & television reception. 
 
CAUTION: 
Changes or modifications not expressly approved by ELC lighting and Leprecon LLC may void the 
users authority to operate this equipment. 
 
R&TTE regulations (433,92MHz EU version): 
 
The HF modules used are designed and manufactured by Radiometrix (UK) and approved to ETS 
300-220-1. 
The transmitter is approved according R&TTE guideline 1999/5/EC and carries the declaration 
CE0889! 
The unit is approved for use in the following countries in Europe: 
A,B,DK,FIN,F, D,EL,IRL,I,L,NL,P,E,S,UK,IS,NO,CH 
 
Technical Specifications: 
 
Focus HAND Remote control transmitter: 
 
Output:  

EU: UHF 433.92 MHz, 10mw maximum 

 

 

US: UHF 914,5 MHz, 1mW maximum 

Antenna: 

Helical, fixed 

Working range: 75 meter indoor, 200 meter in free field 
Power:   

9 Volt 6F22 battery 

Keys:   

16 keys 

Size / Weight:  115 x 65 x 20 mm (excl. antenna) 280 gram 
 
Focus HAND2 Main unit: 
 
Output:  

DMX 512 (1990) on 5 pin female XLR 

Input:   

DMX 512 (1990) on 5 pin male XLR 

Signalization:  3 Leds 
Power:   

90Vac to 240Vac 10VA max 

Dimensions 

200 x 44 x 150 mm 

Weight   

1,4 kg 

Содержание focus HAND 3









Отзывы: