manualshive.com logo in svg

Elation Waterfall 250 Pro, Руководство пользователя, Страница: 5 / 35

Поделиться
Скачать
Elation Waterfall 250 Pro Скачать руководство пользователя страница 5

 
 
 

Waterfall 250 Pro™ 

©Elation Professional®                                                                                                      5                                             

                                               

Waterfall 250 Pro™ 

1. GENERAL INFORMATION 

 

INTRODUCTION

: 

Congratulations, you have just purchased one of the most innovative and 

reliable lighting fixtures on the market today! The Waterfall 250 Pro,™ has been designed to 

perform reliably for years when the guidelines in this booklet are followed. Please read and 

understand the instructions in this manual carefully and thoroughly before attempting to 

operate this unit. These instructions contain important information regarding safety during 

use and maintenance.   

 

UNPACKING:

 Thank you for purchasing the Waterfall 250 Pro™ by Elation Professional®. 

Every Waterfall 250 Pro™ has been thoroughly tested and has been shipped in perfect 

operating condition. Carefully check the shipping carton for damage that may have occurred 

during shipping. If the carton appears to be damaged, carefully inspect your unit for damage 

and be sure all accessories necessary to operate the unit have arrived intact. In the event 

damage has been found or parts are missing, please contact our customer support team for 

further instructions. Please do not return this unit to your dealer without first contacting 

customer support at the number listed below. 

 

CUSTOMER SUPPORT:

 

Elation Professional

®

 provides a customer support line, to provide 

set up help and to answer any question should you encounter problems during your set up or 

initial operation. You may also visit us on the web at www.elationlighting.com for any 

comments or suggestions. For service related issue please contact Elation Professional®. 

Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time. 

 Voice: 

 (323) 

582-3322 

 Fax:  

 (323) 

582-3108 

 E-mail: 

  

[email protected]

 

 Forum: 

 www.ElationLighting.com/forum 

 

Warning

! 

To prevent or reduce the risk of electrical shock or fire, do not expose this unit to 

rain or moisture.   

 

Caution!

 

There are no user serviceable parts inside this unit. Do not attempt any repairs 

yourself, doing so will void your manufactures warranty.   

 

Содержание Waterfall 250 Pro




































Отзывы:

Нет отзывов