background image

14

15

•  If the vent coupling cannot be connected

 Check that there are no foreign objects between the vent coupling and the vent valve. 

Ensure 

correct positioning of the vent coupling on the vent valve

. The vent coupling must be aligned 

straight and coupled onto the vent valve on the vehicle. If you have any doubts or questions, 

please contact the station personnel.

 Ensure that the vent coupling is not damaged. Vent couplings in unsuitable condition must 

not be used. Notify the station personnel or the service contractor.

 Never force operation of the vent coupling

. If the coupling process does not work smoothly, 

disconnect and then re-connect the vent coupling as indicated under 'Operating instructions'. 

If the problem persists notify the station personnel.

•  Leakage

 

 If uncontrolled and / or permanent gas release to the atmosphere occurs, immediately 

stop venting. 

Push emergency button of dispenser immediately, leave area and inform station 

personnel. If area is safe, check tight connection between valve seat and vent coupling as well as 

seals. If the problem persists notify the station personnel.

•  If the vent coupling cannot be disconnected after venting

 

 

Connect vent coupling once again as indicated under chapter 'Operation Instructions'. Then 

try to disconnect and take off the VC-LNG.

 

Check if ice has accumulated around the vent coupling, remove it with compressed air. Then 

try to disconnect and take off the vent coupling after venting.

 

Never force operation of the vent coupling. If the uncoupling process does not work smoothly, 

notify the station personnel.

If self-service is not possible, please contact a service company specialised and certified in 

LNG Service Station installations.

MAINTENANCE

The VC-LNG is a mechanical device that may become inoperative due to wear, corrosion and ageing 

of components. Regular inspections and maintenance are essential for a safe operation.

Daily visual inspections of the vent coupling by trained personnel should be carried out to ensure 

proper function. It’s recommended to clean the vent coupling thoroughly with compressed air regularly 

in order to remove any debris or contamination.

The vent coupling shall be clean and not show any signs of damage (e. g. dents or sharp edges). 

The vent coupling condition shall be thoroughly checked during the annual pump maintenance by 

competent personnel. Applicable laws, regulations and Codes of Practice have to be followed. 

Vent couplings in unfit condition for use must be immediately replaced.

CONDITIONS OF USE

Failure to comply with any warnings, instructions, procedures or any other common sense procedures 

may result in injury, equipment damage, property damage or poor performance of the equipment.

Elaflex Hiby accepts no liability for direct, indirect, incidental, special, or consequential damages 

resulting from failure to follow any warnings, instructions and procedures in this manual, or any other 

common sense procedures generally applicable to equipment of this type. The foregoing limitation 

extends to damages to person or property caused by the unit or damages resulting from the inability 

to use the unit including loss of profits, loss of products, loss of power supply, the cost of arranging 

an alternative power supply, and loss of time, whether incurred by the user or their employees, the 

installer, the commissioner, a service technician, or any third party.

The manufacturer reserves the right to change the specifications of its products or the information in 

this manual without necessarily notifying its users.

Variations in installation and operating conditions may affect the unit‘s performance. Elaflex Hiby has 

no control over each installation‘s unique operating environment. Hence, no representations or war-

ranties concerning the performance of the unit under the actual operating conditions prevailing at the 

installation are made. A technical expert of your choosing should validate all operating parameters 

for each application.

Elaflex Hiby has made every effort to explain all servicing procedures, warnings, and safety precau-

tions as clearly and completely as possible. However, due to the range of operating environments, it 

is not possible to anticipate every issue that may arise. This manual is intended to provide general 

guidance. For specific guidance and technical support, contact your authorized supplier or specialist 

service contractor.

Only approved original parts shall be used and no unauthorized modifications to the hardware shall 

be made. The use of non-approved parts or modifications will void all warranties and approvals. The 

use of non-approved parts or modifications may also constitute a safety hazard.

Information in this manual shall not be deemed a warranty, representation, or guarantee. For warranty 

provisions applicable to this unit, please refer to the warranty provided by the supplier.

Every effort has been made to ensure the accuracy of this document. However, it may contain technical 

inaccuracies or typographical errors. Elaflex Hiby assumes no responsibility for and disclaims all 

liability of such inaccuracies, errors or emissions in this.

WARRANTY 

Elaflex Hiby guarantees against defective materials and manufacturing for 18 months from date of 

supply. If the delivery date cannot be established, the production date applies. The production date 

is marked on the vent coupling body.
Excluded are vent couplings and parts subjected to wear and tear and damages caused by improper 

use, for example the use with unsuitable media. Furthermore excluded are indirect damages and 

costs, such as travelling related to exchange and repair work. We refuse any liability for consequential 

loss or damage resulting from the use of our vent coupling.

Содержание VC-LNG










Отзывы: