Revision 1.1, Released on 15
th
of April, 2016.
STEP 4: MOUNT THE EK-XRES 100/140 Revo D5 RESERVOIR INTO THE COMPUTER CHASSIS
By default the EK-XRES Revo D5 ships with EK-Revo D5 Holder. This holder is meant to be installed directly on the computer chassis. User may need to drill 4 (four) Φ5 mm
(enclosed sticker with designated holes) holes through the metal chassis using electric power drill if there are no appropriate mounting holes available. EK recommends users
to find an appropriate position in your computer chassis to install the EK-XRES Revo D5 pump assembly.
To sucessfully install the EK-XRES Revo D5 pump/reservoir assembly please complete the following steps:
1.
Find an appropriate position for the unit inside (or perhaps outside) of your computer
chassis; drill mounting holes if needed. Sticker with designated holes position is enclosed.
Before drilling stick it to the Computer chassis.
2.
Attach the EK-Revo D5 Holder to the computer chassis metal frame using enclosed 4
(four) M4x10 DIN7984 screws and PVC washers. Secure the screws using enclosed Allen
key 2.5mm..
3.
Insert the rubber damper into the EK-Revo D5 Holder. Insert the pump into the damper.
And secure it using two M3x12 DIN7984 screws from the side of the holder. Use enclosed
2mm Allen key. Your installation is now complete.
STEP 5: ATTACHING FITTINGS
EK-XRES Revo D5 PWM (incl. pump) series reservoir pump combo featured 3 (three) G1/4 threaded ports on the main body of which 1 (one) is inlet and other is outlet. When
reservoir is in upright position outlet port is positioned lower than inlet port. EKWB recommends using EK-ACF fittings with the EK-XRES Revo D5 PWM series reservoir pump
combo units. To ensure that the tubes are securely attached to the barb/fittings, please use hose clamps or an appropriate substitute.
It is mandatory to use the correct INLET and OUTLET ports:
1.
The OUTLET port (pressure port) is, when the reservoir sits in upright position, positioned
lower than the inlet port.
2.
The INLET port(s) (suction port) is the port with G1/4 threading plane.
3.
Make sure not to use fittings or barbs with G1/4 thread longer than 5mm! All
EK-ACF,
EK-HDC
fittings are compatible!
TIP:
Port on reservoir’s top part is not intended to be used as inlet port. The
aforementioned port should only be used for connecting this reservoir with external fill
port!
IMPORTANT DISCLOSURES:
VERY IMPORTANT NOTICE: Once the installation is completed, it is a recommended practice to test the cooling circuit for leaks prior to powering up the computer. We
recommend a 24 hour leak test prior to powering up the computer. Do not test the water block using tap water pressure. This will rupture the top of the housing and render
the block unusable (and will void your warranty). While all efforts have been made to provide the most comprehensive tutorial possible, EK Water Blocks assumes no liability
expressed or implied for any consequential damage(s) occurring to your equipment as a result of using EK Water Blocks cooling products, either due to errors or omissions on
our part in the above instructions, or due to failure or defect in the EK Water Blocks cooling products.
WARRANTY:Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user. During this
period, products will be repaired or have parts replaced at our discretion provided that: (I) the product is returned to the agent from whom it was purchased; (II) the product
has been purchased by an end user and has not used for commercial purposes; (III) the product has not been misused, handled carelessly, or used in a manner other than in
accordance with the instructions provided describing its installation and proper use. This warranty does not confer rights other than those expressly set out above and does
not cover any claims for consequential loss or damage. This warranty is offered as an extra benefit and does not affect your statutory rights as a consumer. This warranty is
voided if the product comes in contact with aggressive additives or other improper liquids.
Any other RMA issues can be reported to
REQUIRED TOOLS
Allen key 2.5mm, allen key 2mm and allen key 6mm (are enclosed)
power drill with 5mm drill bit or equivalent (optional)
EK-PSC Fitting
EK-Plug G1/4
Computer chassis
metal plate
EK-Revo D5 Holder
M4x10 screw+
washer
Outlet
Inlet
Inlet
Outlet
Mounting holes
