ekwb EK-Quantum Vector TUF RX 6800 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 14

ekwb EK-Quantum Vector TUF RX 6800 Скачать руководство пользователя страница 11

- 11 -

For this Step, you will need:

M 2.5 PVC Washer

(12 pcs)

M2.5 x 4 AX1

Screw (13 pcs)

Phillips Head

Screwdriver

4 mm

STEP 2

M2.5 x 4 AX1

M2.5 PVC WASHER

WITHOUT
PVC WASHER

STEP 2

ATTACHING THE WATER BLOCK

Use thirteen (13) M2.5 x 4 AX1 screws and twelve (12) M2.5

PVC washers. Tighten the screws evenly using the Phillips head

screwdriver. EK recommends you start tightening the screws

around the GPU core first and then continuing outward to prevent

damage to the GPU.

CHECKING THE CONTACT IN CASE OF HIGH TEMPERATURES

If necessary, temporarily remove the water block to check for uniform
surface contact between the block and components. Pay special
attention to the VRM section of the graphics card. Check whether
the water block makes contact with the intended integrated circuit.
Then repeat Steps from the previous section to re-attach the block.

In case you fail to obtain good contact, please check
again or contact our support service at
https://www.ekwb.com/customer-support/.

«
...
9
10
11
12
13
...
»

Содержание EK-Quantum Vector TUF RX 6800















Отзывы:

Нет отзывов