Ekinex SIGNUM KNX Скачать руководство пользователя страница 2

2

0,70 ÷ 1,50 m

min 0,3 m

Delivery

The metal support for wall mounting box (cod. EK-SMQ-

71-S), the fixing screws and the KNX terminal block for 

the connection to the power supply are delivered with the 

device. 

Mounting position

If the integrated sensor is used for temperature regulation, 

the device has to be installed preferably on an internal 

wall at a height between 0.70 and 1.5 m and at least 0.3 

m far from doors. The device can not be installed close to 

heat sources such as radiators or household appliances 

or in position subjected to direct sunlight. If necessary, for 

the regulation can be used a weighted average between 

the value measured by the integrated sensor and a value 

received via bus by another KNX device. 

(*) To be completed with the extension for colour and finishing

SIGNUM with square single plate and 

proximity sensor (*)

with 30 x 60 mm window

Code: EK-EV2-TP... (Deep version)

EK-EV2-TP-S-... (Surface version)

Mounting

The device has degree of protection IP20, and is there

-

fore suitable for use in dry interior rooms. The installation 

of  the  device  can  be  done  with  round  or  square    flush 

mounting box.
To mount the device, please carry out the following ope-

rations:
Deep series
• 

fix the metal support (e) by means of the pair of screws 

(d) on the flush mounting box (g) equipped with suitable 

holes;

•  insert the device (b1) into the support-box assembly 

(e+g), inserting the bus terminal, previously connected 

to the bus cable (see: “Connection to the KNX bus 

line”), in the appropriate seat on the back of the device;

•  screw the device (b1) onto the support-box assembly 

(e+g) using the pair of screws (c) supplied;

•  mount the plate (a), by inserting it from the opposite 

side to that of the proximity sensor (highlighted by the 

slot) and pressing slightly in the sensor area for closure.

Surface series
• 

fix the plastic adapter (f) by means of the pair of screws 

(d) on the flush mounting box (g) equipped with suitable 

holes;

• 

hook the device (b2), previously fixed to the plate (a) 

with suitable screws, to the support-box assembly (f+g) 

using the magnets and inserting the bus terminal, pre-

viously connected to the bus cable (see: “Connection to 

the KNX bus network “), in the special housing on the 

back of the device.

Note. 

The plate for completing the device can be 

ordered with the SIGNUM pushbutton or separa-

tely. For more information on available materials, 

colours and finishes, see also the ekinex

®

 product 

catalog or browse www.ekinex.com.

i

Note. 

The screws supplied in the package are su

-

itable  for  standard  installations.  For  more  specific 

applications, where the screws have to be replaced, 

only flat-head screws must be used. The screws for 

the metal support must be tightened with a max. tor

-

que of 1.0 Nm.

i

a) Deep or Surface series plate (to be ordered separately)

b1), b2) EK-EV2-TP “SIGNUM” pushbutton

c) Screws for fixing the device on the support (Deep series only, in

-

cluded in the delivery)

d) Fixing screws for metal support (Deep) or plastic adapter (Surface) 

on wall mounting box (supplied)(included in the delivery)

e) Metal support for wall mounting box (Deep series only, included 

in the delivery)

f) Adapter in plastic material with magnets for wall mounting obx (Sur-

face series only, included in the delivery)

g) Wall mounting box (not delivered by ekinex)

Installation for Deep or Surface series

b1

e

a

c

d

g

d

f

b2

Finishing plates and proximity sensor

The device has to be ordered with an ekinex

®

 plate in 

metal (aluminum) or Metal HT (chromed), with a 30 x 60 

mm window and integrated proximity sensor. The plate is 

available for Deep or Surface series mounting and can be 

ordered either with SIGNUM or separately.

Note. 

The device can be mounted with the window 

on the right side, by rotating both the pushbutton 

and the plate by 180 °. In this case, the proximity 

sensor and its slot will be located in the upper part 

of the panel, instead of at the bottom.

i

Содержание SIGNUM KNX









Отзывы: