Ekinex EK-CG2-TP Скачать руководство пользователя

Страница: 37 / 91

Applicatio Manual

Universal Interface 4 DIN/NTC EK- CG2-TP

Revisione 1.0.0 - Aggiornato: 04/09/2017

MAEKCG2TP_EN

Pag. 37

9.1.4 Independent or single: dimming

Parameter name

Conditions

Values

Long press time

Input x = independent or single

Type = dimming

hh:mm:ss.fff

(

00:00:03.000

)

Minimum push time for a press in order to be recognized as a long press.

Toggle mode

Input x = independent or single

Type = dimming

enabled /

disabled

When enabled, causes the short press to toggle the on-off status of the destination CO; otherwise, a
fixed status can be assigned to the short press.

Long action

Input x = independent or single

Type = dimming

Toggle mode = enabled

darker

brighter

darker ↔

brighter

Defines the function to be assigned to the long press. If the toggle mode is enabled, the Short press
action is already defined as toggle.

Short / Long action

Input x = independent or single

Type = dimming

Toggle mode = disabled

off / darker

on / brighter

off / darker ↔

brighter

on / darker ↔

brighter

Defines the function to be assigned to the long and short press.

Send cyclically

Input x = independent or single

Type = dimming

none

off / value 1
on / value 2

both off and on / both values

Defines which of the values, if any, must be cyclically retransmitted whenever activated.

Cyclic sending interval

Input x = independent or single

Type = dimming

Send cyclically ≠ none

hh:mm:ss (

00:02:00

)

Interval between cyclical transmissions.

Lock function

–

Behaviour at locking

Input x = independent or single

Type = dimming

none

off
on

toggle

Value to be assigned to the object when a locking command is received.

Lock function

–

Behaviour at unlocking

Input x = independent or single

Type = dimming

none

off
on

as previous

Value to be assigned to the object when an unlocking command is received.

Содержание EK-CG2-TP




























































































Результаты поиска

Содержание EK-CG2-TP

Отзывы:

Похожие инструкции для EK-CG2-TP

Бренды по названию

Популярные бренды

Ekinex EK-CG2-TP, Руководство по применению

Результаты поиска

Содержание EK-CG2-TP

Отзывы:

Похожие инструкции для EK-CG2-TP

Бренды по названию

Популярные бренды