_ Electric Ovens _ rev. 2 ______________________________________________________________ KF 725 UD _
_____________________________________________________________________________________ page 5 _
4.
4.
4.
4. Instructions for the installer
Instructions for the installer
Instructions for the installer
Instructions for the installer
The following instructions are aimed at the qualified installer, to ensure that he carries
out the installation, adjustment and maintenance operations as correctly as possible and
according to current legal regulations. Any operation must be performed with electrical
power cut to the appliance.
Before using the appliance, carefully remove the special adhesive film protecting the parts
in stainless steel. Do not leave any glue residues on the surfaces. If necessary, remove them
at once, with an appropriate solvent.
Fitting the feet
Fitting the feet
Fitting the feet
Fitting the feet - The feet are inside the appliance and must be secured on the four
threaded holes on the base. If necessary, the height of the feet can be adjusted by screwing
or unscrewing.
Positioning
Positioning
Positioning
Positioning - Position the appliance perfectly horizontally on a table or similar support (the
table or support must be at least 85 cm above the floor). Position it at a distance of not less
than 10 cm from the side and rear walls, to enable natural ventilating air to circulate freely
around it. The appliance is ventilated through specific openings on the metal walls of the
outer housing , and ensures efficiency and long-life. For this reason it is strictly forbidden to
obstruct these ventilation openings, even partially or for short periods. Failure to observe th
Failure to observe th
Failure to observe th
Failure to observe this
is
is
is
specific prohibition releases the manufacturer of the appliance from all responsibility and
specific prohibition releases the manufacturer of the appliance from all responsibility and
specific prohibition releases the manufacturer of the appliance from all responsibility and
specific prohibition releases the manufacturer of the appliance from all responsibility and
immediately voids any guarantee rights for the said appliance,
immediately voids any guarantee rights for the said appliance,
immediately voids any guarantee rights for the said appliance,
immediately voids any guarantee rights for the said appliance, because its constructive
conformity has been voluntarily compromised. Furthermore, the appliance is not suitable for
embedding and for grouped positioning with other identical appliances.
Electrical connection
Electrical connection
Electrical connection
Electrical connection - The appliance must be connected to the electrical mains according
to current legal regulations. Before making the connection, make sure of the following:
-
the voltage and frequency values of the power supply system match the values on
the "technical data" plate affixed on the appliance;
-
the limiting valve and the system are able to support the appliance's load (see the
"technical data" plate);
-
th
th
th
the power supply system has an adequate earth connection according to current
e power supply system has an adequate earth connection according to current
e power supply system has an adequate earth connection according to current
e power supply system has an adequate earth connection according to current
legal regulations;
legal regulations;
legal regulations;
legal regulations;
-
a omnipolar switch with minimum between-contacts aperture of the overvoltage
category III (4000 V), sized to the load and conforming to current legal regulations, is
fitted between the appliance and the mains in the direct connection to the mains;
-
the omnipolar switch used for connection is easy to reach when the appliance is
installed;
-
the yellow/green earth wire is not interrupted by the switch;
the yellow/green earth wire is not interrupted by the switch;
the yellow/green earth wire is not interrupted by the switch;
the yellow/green earth wire is not interrupted by the switch;
-
the power supply, when the appliance is operating, must not deviate from the rated
voltage value by ±10%;
-
make sure that after inserting the power supply cord into the terminal block it does
not come into contact with any of the cooking range's hot parts;
-
if the supply ca
if the supply ca
if the supply ca
if the supply cable is damaged then it must be replaced by the manufacturer or by
ble is damaged then it must be replaced by the manufacturer or by
ble is damaged then it must be replaced by the manufacturer or by
ble is damaged then it must be replaced by the manufacturer or by
your technical support or by a qualified person to avoid any risk.
your technical support or by a qualified person to avoid any risk.
your technical support or by a qualified person to avoid any risk.
your technical support or by a qualified person to avoid any risk.
Connection to water mains
Connection to water mains
Connection to water mains
Connection to water mains - The oven must be supplied with softened drinking water
with a hardness value of 0.5 to 5°F (it is obligatory to use water softener to reduce the
formation of scaling inside the cooking chamber). The water pressure must be in the range
of 150 to 250 kPa (1.5 – 2.5 bar). If the water pressure exceeds 2.5 bar, install a pressure
reducer device upstream. If the pressure is below 1.5 bar, use a pressure pump to increase
the level.
