EK-Quantum Vector2 XC3 RTX 3080 D-RGB Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 20

background image

- 17 -

INSERTING THE GRAPHICS CARD INTO THE CHASSIS

Carefully lift your graphics card with the installed water block and insert it into
your PC’s motherboard PCI Express expansion slot. Please keep in mind that
your graphics card is heavier than before it was equipped with the water block.

You need to be very careful when handling the graphics
card. Avoid all unnecessary manipulation of the water block
assembly that might damage your card or water block.

FITTINGS AND TUBING

STEP 1

Screw-in two (2) G1/4 threaded male fittings. Attach the liquid
cooling tubes and connect the water block to the cooling loop.

Do not forget to plug the remaining two openings using
the enclosed EK-Plug G1/4 or its equivalent.

EK recommends using EK fittings with all EK water blocks.

CAUTION: When using connectors other than EK fittings,
pay special attention to the length of the fittings’ male G1/4”
thread – 5mm is the maximum G1/4” thread length allowed!

STEP 1

TUBING

EK- PLUG G1/4

EK-FITTING

For this step, you will need:

EK-Loop Multi Allen Key

«
...
15
16
17
18
19
...
»

Содержание Vector2 XC3 RTX 3080 D-RGB





















Отзывы:

Нет отзывов

Похожие инструкции для Vector2 XC3 RTX 3080 D-RGB

C50FSi - VB Network Camera

Бренд: Canon Страницы: 32

Бренд: Rabbit Страницы: 120

Enterprise Filter Authentication R3000

Бренд: 8e6 Technologies Страницы: 66

Бренд: FabiaTech Страницы: 4

Бренд: LaCie Страницы: 44

LaCie Ethernet Disk

Бренд: LaCie Страницы: 2

SATA II ExpressCard 34

Бренд: LaCie Страницы: 2

12big Rack Fibre 8

Бренд: LaCie Страницы: 9

OfficeConnect WX2200

Бренд: 3Com Страницы: 204

Бренд: NEC Страницы: 6

Бренд: Ubiquiti Страницы: 23

Wisenet PRN-6400B4

Бренд: Hanwha Techwin Страницы: 14

Бренд: ZALMAN Страницы: 9

iCE40 SPRAM Series

Бренд: Lattice Semiconductor Страницы: 12

Бренд: Sony Ericsson Страницы: 93

Бренд: JAKA Страницы: 37

H8S/2646 Series

Бренд: Renesas Страницы: 20

Бренд: Rockwell Automation Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды