![background image](http://html1.mh-extra.com/html/einhell/te-ac-270-50-10/te-ac-270-50-10_operating-instructions-manual_2370176028.webp)
GB
- 28 -
4. Technical data
Noise
The noise emission values were measured in ac-
cordance with EN ISO 2151.
5. Before starting the equipment
Warning!
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
•
Examine the machine for signs of transit da-
mage. Report any damage immediately to the
company which delivered the compressor.
•
The compressor should be set up near the
working consumer.
•
Avoid long air lines and long supply lines (ex-
tensions).
•
Make sure the intake air is dry and dust-free.
•
Do not set up the compressor in damp or wet
rooms.
•
The compressor may only be used in suitable
rooms (with good ventilation and an ambient
temperature from +5°C to +40°C). There must
be no dust, acids, vapors, explosive gases or
inflammable gases in the room.
•
The compressor is designed to be used in dry
rooms. It is prohibited to use the compressor
in areas where work is conducted with spray-
ed water.
•
The oil level in the compressor pump has to
be checked before putting the equipment into
operation.
•
The equipment must be set up where it can
stand securely.
•
Use flexible hoses in order to prevent trans-
mitting unacceptable loads to the pipeline
system at the connection between the com-
pressor system and the pipeline system.
•
It is essential to use separators, traps and
drains which process the liquids produced by
the compressor before the compressor sys-
tem is put into operation.
•
Supply hoses at pressures above 7 bar
should be equipped with a safety cable (e.g.
a wire rope).
6. Assembly and starting
Important!
You must fully assemble the appliance before
using it for the
fi
rst time.
6.1 Fitting the wheels (3)
Fit the supplied wheels as shown in Fig. 5.
6.2 Fitting the supporting feet (4)
Fit the supplied supporting feet (4) as shown in
Fig. 6.
6.3 Fitting the transport handle (9)
Screw the transport handle (9) to the compressor
as shown in Figures 7 to 8.
6.4 Replacing the oil sealing plug (14)
Remove the transportation cover from the oil
fi
ller
opening with a screwdriver and insert the sup-
plied oil sealing plug (14) into the oil
fi
ller opening
(Fig. 9/11).
6.5 Fitting the air
fi
lter (1)
Use a screwdriver to remove the transportation
cover from the air
fi
lter connection.
Screw in the supplied air
fi
lter (Fig.10).
6.6 Power supply
•
The motor is fitted with an overload switch
(Fig. 3/Item 6). If the compressor overloads,
the overload switch switches off the equip-
ment automatically to protect the compressor
from overheating. If the overload switch trig-
gers, switch off the compressor using the ON/
OFF switch (8) and wait until the compressor
cools down. Then press the overload switch
(16) and restart the compressor.
•
Long supply cables, extensions, cable reels
etc. cause a drop in voltage and can impede
motor start-up.
•
In the case of low temperatures below +5°C,
motor start-up is jeopardized as a result of
stiffness.
6.7 On/O
ff
switch (8)
To switch on the compressor, pull out the knob
(8).
To switch o
ff
the compressor, press the knob (8)
back in. (Figure 2)
Anl_TE_AC_270_50_10_SPK8.indb 28
Anl_TE_AC_270_50_10_SPK8.indb 28
13.05.2019 14:52:14
13.05.2019 14:52:14
Содержание TE-AC 270/50/10
Страница 45: ...45 Anl_TE_AC_270_50_10_SPK8 indb 45 Anl_TE_AC_270_50_10_SPK8 indb 45 13 05 2019 14 52 14 13 05 2019 14 52 14...
Страница 46: ...46 Anl_TE_AC_270_50_10_SPK8 indb 46 Anl_TE_AC_270_50_10_SPK8 indb 46 13 05 2019 14 52 14 13 05 2019 14 52 14...
Страница 47: ...47 Anl_TE_AC_270_50_10_SPK8 indb 47 Anl_TE_AC_270_50_10_SPK8 indb 47 13 05 2019 14 52 14 13 05 2019 14 52 14...