GB
- 20 -
6. Assembly and starting
Important!
You must fully assemble the appliance before
using it for the
fi
rst time.
6.1 Fitting the wheels (3)
Fit the supplied wheels as shown in Fig. 5.
6.2 Fitting the supporting feet (4)
Fit the supplied supporting feet (4) as shown in
Fig. 6.
6.3 Fitting the transport handle (9)
Screw the transport handle (9) to the compressor
as shown in Figures 7 to 8.
6.4. Replacing the oil sealing plug (14)
Remove the transportation cover from the oil
fi
ller
opening with a screwdriver and insert the sup-
plied oil sealing plug (14) into the oil
fi
ller opening
(Fig. 9/11).
6.5 Fitting the air
fi
lter (1)
Use a screwdriver to remove the transportation
cover from the air
fi
lter connection.
Screw in the supplied air
fi
lter (Fig. 10).
6.6. Power supply
•
The motor is fitted with an overload switch
(Fig. 3/Item 6). If the compressor overloads,
the overload switch switches off the equip-
ment automatically to protect the compressor
from overheating. If the overload switch trig-
gers, switch off the compressor using the ON/
OFF switch (8) and wait until the compressor
cools down. Then press the overload switch
(16) and restart the compressor.
•
Long supply cables, extensions, cable reels
etc. cause a drop in voltage and can impede
motor start-up.
•
In the case of low temperatures below +5°C,
motor start-up is jeopardized as a result of
stiffness.
6.7 On/O
ff
switch (8)
To switch on the compressor, pull out the knob
(8).
To switch o
ff
the compressor, press the knob (8)
back in. (Figure 2)
6.8 Adjusting the pressure: (Fig. 1,2)
•
You can adjust the pressure on the pressure
gauge (6) using the pressure regulator (7).
•
The set pressure can be taken from the quick-
lock coupling (5).
6.9 Setting the pressure switch
The pressure switch is set at the factory.
Switch-on pressure 8 bar
Switch-o
ff
pressure 10 bar
7. Replacing the power cable
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Important!
Pull the power plug before doing any
cleaning and maintenance work on the ap-
pliance.
Important!
Wait until the compressor has completely
cooled down. Risk of burns!
Important!
Always depressurize the tank before carrying
out any cleaning and maintenance work.
Important!
After use, always switch o
ff
the equipment
immediately and pull out the power plug.
8.1 Cleaning
•
Keep the safety devices free of dirt and dust
as far as possible. Wipe the equipment with a
clean cloth or blow it with compressed air at
low pressure.
•
We recommend that you clean the appliance
immediately after you use it.
•
Clean the appliance regularly with a damp
cloth and some soft soap. Do not use
cleaning agents or solvents; these may be
aggressive to the plastic parts in the appli-
ance. Ensure that no water can get into the
interior of the appliance.
•
You must disconnect the hose and any
spraying tools from the compressor before
cleaning. Do not clean the compressor with
Anl_TE_AC_270_24_10_SPK1.indb 20
Anl_TE_AC_270_24_10_SPK1.indb 20
19.09.13 18:23
19.09.13 18:23
Содержание TE-AC 270/24/10
Страница 13: ...D 13 Anl_TE_AC_270_24_10_SPK1 indb 13 Anl_TE_AC_270_24_10_SPK1 indb 13 19 09 13 18 23 19 09 13 18 23 ...
Страница 92: ... 92 Anl_TE_AC_270_24_10_SPK1 indb 92 Anl_TE_AC_270_24_10_SPK1 indb 92 19 09 13 18 23 19 09 13 18 23 ...
Страница 93: ... 93 Anl_TE_AC_270_24_10_SPK1 indb 93 Anl_TE_AC_270_24_10_SPK1 indb 93 19 09 13 18 23 19 09 13 18 23 ...
Страница 94: ...EH 09 2013 01 Anl_TE_AC_270_24_10_SPK1 indb 94 Anl_TE_AC_270_24_10_SPK1 indb 94 19 09 13 18 23 19 09 13 18 23 ...
