EINHELL TC-WD 150, Оригинальная инструкция по эксплуатации

Страница: 22 / 170

GB
- 22 -
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched o ff and times in which the tool is
switched on but operates without load).
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment’s construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
Warning!
Always pull the power plug before making
adjustments to the equipment.
Pull the power plug before doing any mainte-
nance or assembly work on the equipment.
•
The equipment has to be set up where it can
stand securely.
•
Before starting work, firmly screw the grin-
ding/sanding machine to the workbench or
equivalent using the 4 mounting holes (8) in
the base plate (9).
•
All covers and safety devices have to be pro-
perly fitted before the equipment is switched
on.
•
It must be possible for the grinding/sanding
wheel to run freely.
•
Check that the voltage on the rating plate is
the same as your supply voltage before you
connect the equipment to the power supply.
•
Fit the sealing plug (21) on the underside of
the water container (10). This needs to be
pressed in with a little force.
5.1 Assembling the spark de fl ector / safety
window (Fig. 3/4)
•
Fasten the spark deflector (3) to the machine
(Fig. 3).
•
To do this, use the socket head screws (11),
washers (12), spring washers (13) and nuts
(14).
•
Tighten the screw connection using a 4 mm
hex key and an 8 mm wrench. Note! Not
supplied.
•
Fit the safety window (2) to the spark deflec-
tor (3) using a lock screw (15), a washer (12),
a spring washer (13) and a locking button
(16) (Fig. 4).
5.2 Adjusting the spark de fl ector (Fig. 5)
•
With the help of the slots in the spark deflec-
tor (3) you can adjust it in vertical direction.
•
To do so, slacken the socket head screws
(11) and push the spark deflector as close as
possible to the grinding/sanding wheel (5).
•
Warning! The distance between the grinding/
sanding wheel (5) and the spark deflector (3)
must be set as small as possible and under
no circumstances should it exceed 2 mm.
•
Then secure the spark deflector (3) again.
•
Warning! Adjust the spark deflector (3) peri-
odically to compensate for wear on the grin-
ding/sanding wheel (5).
5.3 Fitting the workpiece support (Fig. 6)
•
Fit the workpiece support (7) to the machine.
•
Warning! The angled face of the workpiece
support must point away from the grinding/
sanding wheel (5)!
•
To achieve this, use the lock screw (17), the
washer (18), the spring washer (19) and the
locking button (20).
5.4 Setting the workpiece support (Fig. 7)
•
With the help of the slot in the workpiece
support (7) you can adjust it in horizontal
direction.
•
To do so, slacken the locking button (20) and
Anl_TC_WD_200_150_SPK9.indb 22 Anl_TC_WD_200_150_SPK9.indb 22 23.06.2020 15:30:18 23.06.2020 15:30:18