EINHELL TC-TS 2025/2 U, Оригинальная инструкция по эксплуатации

Страница: 29 / 204

GB
- 29 -
wobbly.
•
The splitter (5) must be positioned in the cen-
ter along an imaginary line extending behind
the saw blade (4), so that it is not possible for
the material to get jammed.
•
The gap between the blade (4) and the split-
ter (5) should be 3 mm to 8 mm. (Fig. 11c).
•
Refit the table insert (6) and the saw blade
guard (2) (see 6.4, 6.6)
6.6 Fitting/changing the saw blade guard
(Fig. 13)
•
Mount the saw blade guard (2) on the splitter
(5) so that the screw fits through the hole (18)
in the splitter.
•
Then insert the screw on the saw blade guard
(2) through the hole (18) and tighten it.
•
Important! The maximum depth that the
screw can be screwed in has been preset at
the factory, so that the saw blade guard (2) is
always able to move freely.
•
Warning! The saw blade guard (2) must al-
ways lower to the workpiece automatically
under its own weight.
6.7 Fitting/changing the saw blade (Fig. 14)
•
Before changing the saw blade: Pull out the
power plug!
•
Wear work gloves to prevent injury when
changing the saw blade.
•
Using the hand wheel (8), set the saw blade
(4) to the maximum cutting depth.
•
Remove the saw blade guard, table insert
and splitter (see 6.6, 6.4, 6.5)
•
Undo the screw (15) with a wrench (38) on
the screw (15) itself and a second wrench
(39) on the motor shaft to apply counter-
pressure.
•
Caution! Turn the screw (15) in the direction
of rotation of the saw blade.
•
Take off the outer flange and pull the old saw
blade (4) off the inner flange.
•
Clean the blade flange thoroughly before fit-
ting the new blade.
•
Fit and fasten the new saw blade (4) in rever-
se order.
•
Important! Note the running direction. The
cutting angle of the teeth must point in run-
ning direction, i.e. forwards (see the arrow on
the blade guard).
•
Refit and set the splitter, table insert and saw
blade (see 6.5, 6.4, 6.6).
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
•
Warning! Every time that you change the saw
blade, check that the saw blade guard (2)
opens and closes again in accordance with
requirements. Also check that the saw blade
(4) spins freely in the saw blade guard (2).
•
Warning! Every time that you change the saw
blade (4), check to see that it spins freely in
the table insert (6) in both perpendicular and
45° angle settings.
•
Warning! You should replace the table insert
(6) immediately whenever it is worn or dama-
ged (see 6.4).
•
Warning! The work to change and align the
saw blade (4) must be carried out correctly.
6.8 Putting away loose parts (Fig. 15)
•
When not in use, the parallel stop (7) and
stop rail (23) can both be secured as shown
in Fig. 15a.
•
The cross stop (14), push stick (3) and the
two wrenches (38+39) can be secured as
shown in Fig. 15b.
6.9 Connection for dust extractor (Fig. 2, 9,
26)
A connection for a dust extractor is provided on
the extractor adapter on the housing (16) and on
the saw blade guard (2).
6.9.1 Dust extraction using a wet & dry vac
(Fig. 2, 9)
•
A wet & dry vac is not supplied with the pro-
duct and is available as an accessory.
•
Attach the suction hose (10) to the machine
as described in 6.3.
•
Connect the wet & dry vac to the extractor
adapter on the housing (16).
6.9.2 Dust extraction using a vacuum ext-
raction system and extractor adapter set
(Fig. 9, 26)
•
The product is not supplied with an extractor
adapter set or a vacuum extraction system,
which are available as accessories.
•
Attach the suction hose (10) to the machine
as described in 6.3.
•
Attach the adapter (c) of the adapter set to
the extractor adapter on the housing (16).
•
A vacuum extraction system can now be
connected to the 100 mm diameter of the
adapter (c).
Anl_TC_TS_2025_2_U_SPK9.indb 29 Anl_TC_TS_2025_2_U_SPK9.indb 29 26.09.2019 10:55:52 26.09.2019 10:55:52