EINHELL TC-SM 2534 Dual, Оригинальная инструкция по эксплуатации, Страница: 36 / 64

GB
- 36 -
Important!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
1. Safety regulations
Caution!
Read all safety regulations and instructions.
Any errors made in following the safety regula-
tions and instructions may result in an electric
shock, fi re and/or serious injury.
Keep all safety regulations and instructions
in a safe place for future use.
Special information about the laser
Important: Laser radiation
Do not look into the beam
Laser class 2
Attention!
Radiation Laser
Do not look at the Laser beam!
Specification Laser according
EN 60825-1 Class: 2 LDBXQ03B
Ǹ
: 650 nm;
Ɠ̞ʸÃ
•
Never look directly into the laser path.
•
Never direct the laser beam at reflecting
surfaces or persons or animals. Even a low
output laser beam can inflict injury on the eye.
•
Caution: It is vital to follow the work proce-
dures described in these instructions. Using
the equipment in any other way may result in
hazardous exposure to laser radiation.
•
Never open the laser module.
•
It is prohibited to carry out any modifications
to the laser to increase its power.
•
The manufacturer cannot accept any liability
for damage due to non-observance of the
safety information.
SAFETY INSTRUCTIONS
Warning! When using electric tools, basic
safety precautions should always be fol-
lowed to reduce the risk of fi re, electric
shock and personal injury, in-cluding the
following. Read all these instructions before
attempting to operate this product and safe
these instructions.
1. Keep work area clean
– Cluttered areas and benches invite injuries.
2. Consider work area environment
– Don‘t expose power tools to rain. Don‘t use
power tools in damp or wet locations. Keep
work area well lit. Don‘t use power tools in
presence of fl ammable liquids or gases.
3. Guard against electric shock
– Prevent body contact with grounded sur-
faces (e.g. pipes, radiators, ranges refrigerati-
ors).
4. Keep children away
– Do not let visitors contact tool or extension
cord. All visitors should be kept away from
work area.
5. Store idle tools
– When not is use, tools should be stored in
dry, high, or locked-up place, out of the reach
of children.
6. Don‘t force tool
– It will do the job better and safer at the rate
for which it was intended.
7. Use right tool
– Don‘t force small tools or attachments to do
the job of heavy duty tool. Don‘t use tools for
purposes not intended: for example, don‘t use
circular saw for cutt- ing tree limbs or logs.
8. Dress properly
– Do not wear loose clothing or jewelry. They
can be caught in moving parts. Rubber gloves
and nonskid footwear are recommended
when working outdoors. Wear protective nair
covering to contain long hair.
9. Use safety glasses
– Also use face or dust mask if cutting opera-
tion is dusty.
10. Don‘t abuse cord
– Never carry tool by cord or yank it to discon-
nect it from receptacle. Keep cord from heat,
oil and sharp edges.
11. Secure work
– Use clamps or a vise to hold work. It‘s safer
than using your hand and it frees both hands
to operate tool.
Anl_TC_SM_2534_Dual_SPK8.indb 36 Anl_TC_SM_2534_Dual_SPK8.indb 36 15.03.16 12:07 15.03.16 12:07