![background image](http://html1.mh-extra.com/html/einhell/tc-ll-2/tc-ll-2_operating-instructions-manual_2371031018.webp)
GB
- 18 -
6. Operation
6.1 Switching On/O
ff
(Fig. 1)
Switching on:
•
Place the laser on a flat surface or fit it to the
universal clamp and fasten it as described
in 5.2.
•
To switch the laser on, push the On/Off switch
to the left (viewed from the front). The lasers
switch on, the green LED (4) comes on and
the pendulum will no longer be blocked,
which means the laser can be aligned.
•
Press the button (5) to display or hide the ver-
tical or horizontal lines again individually.
Switching o
ff
:
To switch o
ff
, push the On/O
ff
switch back to
the position on the right (viewed from the front).
The lasers switch o
ff
and the pendulum will be
blocked.
Important!
To prevent damage during transport or storage,
the equipment must always be switched o
ff
as
described above.
6.2 Automatic alignment of the laser (Fig. 4)
After the laser has been switched on with the On/
O
ff
switch (1), the lasers are aligned automatically
by the pendulum so that the vertical and horizon-
tal lines are displayed level on the wall. (See Fig.
4)
Press the button (5) to display or hide the vertical
or horizontal line individually.
Important!
Make sure that the equipment is never tilted more
than 4 degrees or stands at an angle. If this is the
case, the laser beams will
fl
ash and the LED (4)
will light up red.
6.3 Manual alignment of the laser (Fig. 5)
The laser can also be aligned manually, to ena-
ble a diagonal line to be displayed. Proceed as
follows:
•
Place the laser on a flat surface or fit it to the
universal clamp and fasten it as described
in 5.2.
•
To switch the equipment on, push the On/Off
switch (1) to the left (viewed from the front).
•
Wait until the lasers are aligned and then
move the On/Off switch (1) back to the right.
•
Now press the button (5). The lasers switch
on and the LED (4) lights up red, because the
pendulum is blocked.
•
Now you can tilt the laser to the angle you
require, so that the lines are displayed diago-
nally on the wall. (See Fig. 5)
•
Press the button (5) to hide or display the ver-
tical or horizontal line individually or to switch
the equipment off again.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Maintenance
There are no parts inside the equipment which
require additional maintenance.
7.3 Ordering spare parts and accessories
Please provide the following information when
ordering spare parts:
•
Type of unit
•
Article number of the unit
•
ID number of the unit
•
Spare part number of the required spare part
For our latest prices and information please go to
www.Einhell-Service.com
Anl_TC_LL_2_SPK9.indb 18
Anl_TC_LL_2_SPK9.indb 18
22.04.2021 10:04:29
22.04.2021 10:04:29
Содержание TC-LL 2
