4. Important notes
Safety information
IMPORTANT!
Whenever you use electric tools it is
imperative to take basic safety precautions in order
to reduce the risk of fire, electric shock and personal
injury.
The corresponding safety information can be found
in the enclosed booklet.
CAUTION!
Read all safety regulations and instructions.
Any errors made in following the safety regulations
and instructions may result in an electric shock, fire
and/or serious injury.
Keep all safety regulations and instructions in a
safe place for future use.
5. Technical data
Voltage:
230V ~ 50 Hz
Power:
740 W
Ideal speed no:
1400 min
-1
Blade length:
2240 mm
Max. blade width:
6,5 - 20 mm
Blade speed:
370/800 m/min
Cutting height:
5 -170 mm / 90°
70 mm / 45°
Throat:
305 mm
Table size:
520 x 400 mm
Tilting range of table:
0° to 45°
Workpiece size:
600 x 600 mm
Weight:
52 kg
Noise emission values
Cutting
Sound pressure level L
pA
92,7 dB(A)
Sound power level L
WA
102,3 dB(A)
6. Before putting the machine into
operation
앬
Make sure the machine stands securely, i.e. bolt
it to a workbench or solid base. There are two
holes for this purpose in the machine foot.
앬
The saw table must be mounted correctly.
앬
All covers and safety devices have to be properly
fitted before the machine is switched on.
앬
It must be possible for the blade to run freely.
앬
When working with wood that has been
processed before, watch out for foreign bodies
such as nails or screws etc.
앬
Before you actuate the On/Off switch, make sure
that the saw blade is correctly fitted and that the
machineʼs moving parts run smoothly.
앬
Before you connect the machine to the power
supply, make sure the data on the rating plate is
the same as that for your mains.
7. Assembly
CAUTION!
Pull out the power plug before carrying out any
maintenance, resetting or assembly work on the
bandsaw!
7.1 Assembly of the sub-frame and wheels (Fig.
3-5/27)
First attach the legs (21) loosely to the base
plate (5) of the machine using 2 screws for each
leg. Use the round head M8x12 screws to do so.
Screw the 2 long struts (41) and the 2 short
struts (42) loosely to the legs (21). The doubled-
over part of the struts must be at the top.
Attach rubber feet to the legs (21).
Place the machine on the legs.
Align the entire base frame and tighten all
screws.
Screw the wheels (10) on the rear of the
machine to the legs (21) as shown in Fig. 4.
Screw the transport handle (44) to the rear of
the machine using 2 screws (49).
Fasten the holder (29) for the push stick (28) as
follows: Screw the lock nut onto the bolt (29)
and then screw this into the housing until the
push stick (28) can be hung up.
7.2 Assembling the saw table (Figures 6-9)
Slacken the wing nuts (45) on the underside of
the saw table (15) and remove the chain bar (2)
from the saw table.
Lead the blade through the slot (a) in the
machine table and place the machine table on
the table guide so that the clamping screw (47)
fits through the mounting (48).
Screw the saw table tight with the wing nut (18).
Place the chain bar (2) on the saw table (15) so
that the screw heads (50) slide into the guide
slots (51).
Check that the blade (25) runs freely and does
GB
16
Anleitung RT-SB 305 U_SPK1:_ 03.10.2008 9:40 Uhr Seite 16
