![background image](http://html.mh-extra.com/html/einhell/gc-mt-1636-1/gc-mt-1636-1_original-operating-instructions_2371066019.webp)
GB
- 19 -
plug after every 50 hours of operation.
•
Pull off the spark plug boot (Fig. 9) with a
twist.
•
Remove the spark plug (Fig. 9/Item D) with
the supplied spark plug wrench.
•
Assemble in reverse order.
7.2.3 Changing the oil and checking the oil
level (before using the machine)
The motor oil is best changed when the motor is
at working temperature.
•
Take out the dip stick (Fig. 10a / Item E).
•
Open the drain screw (Fig. 10a / Item F) and
allow the warm oil to drain into a drip tray.
•
Close the drain screw again when all the was-
te oil has been drained.
•
Fill up with engine oil as far as the top mark
on the dip stick (Fig. 10b/H).
•
Important: Do not screw the dip stick when
you check the oil level, simply insert it as far
as the thread (H = Max. / L= Min.).
•
Dispose of the waste oil properly.
7.2.4 Adjusting the Bowden wires
In the working setting it should be possible to
push the clutch lever up to the push bar without
this requiring much e
ff
ort. If the Bowden wire is
too taut for this, it must be extended. To do this,
undo the lock nut opposite the main cable, extend
the screw connector and then tighten the lock nut
again (see Fig. 5e). If the star-type hoes no longer
rotate then the screw connector will have to be
shortened again (as described above).
7.2.5 Power cultivator gearing
The gear unit is driven by a V-belt. The gear unit
can be repaired if this should become necessary.
If repairs are necessary, please contact our custo-
mer service center.
7.3 Storage
Empty the fuel tank before you decommission the
unit for a lengthy period of time. Clean the unit
and coat all the metal parts with a thin
fi
lm of oil to
prevent them rusting.
Store the unit in a clean, dry room.
7.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
8. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
be taken to a suitable collection center for proper
disposal. If you do not know the whereabouts of
such a collection point, you should ask in your
local council o
ffi
ces.
Anl_GC_MT_1636_1_SPK9.indb 19
Anl_GC_MT_1636_1_SPK9.indb 19
29.09.2017 09:21:53
29.09.2017 09:21:53
Содержание GC-MT 1636/1
Страница 123: ... 123 Anl_GC_MT_1636_1_SPK9 indb 123 Anl_GC_MT_1636_1_SPK9 indb 123 29 09 2017 09 22 07 29 09 2017 09 22 07 ...
Страница 124: ... 124 Anl_GC_MT_1636_1_SPK9 indb 124 Anl_GC_MT_1636_1_SPK9 indb 124 29 09 2017 09 22 07 29 09 2017 09 22 07 ...
Страница 125: ... 125 Anl_GC_MT_1636_1_SPK9 indb 125 Anl_GC_MT_1636_1_SPK9 indb 125 29 09 2017 09 22 07 29 09 2017 09 22 07 ...
Страница 126: ...EH 09 2017 01 Anl_GC_MT_1636_1_SPK9 indb 126 Anl_GC_MT_1636_1_SPK9 indb 126 29 09 2017 09 22 07 29 09 2017 09 22 07 ...