![background image](http://html.mh-extra.com/html/einhell/bt-rh-920-e/bt-rh-920-e_operating-instructions-manual_2371620012.webp)
12
GB
6.3 Preselecting the speed (Fig. 6/Item 11)
The speed setting ring (11) enables you to define
the maximum speed. The ON/OFF switch (4) can
only be pressed to the defined maximum speed
setting.
Set the speed using the setting ring (11) on the
ON/OFF switch (4).
Do not attempt to make this setting whilst the drill
is in use.
6.4 Clockwise/Counter-clockwise switch
(Fig. 7/Item 9)
Change switch position only when the drill is
at a standstill!
Switch the direction of the hammer drill using the
clockwise/counter-clockwise switch (9):
Direction Switch
position
Clockwise (forwards and drill)
A
Counter-clockwise (reverse)
B
6.5 Drill / Hammer drill / Chisel selector switch
(Fig. 8)
For drilling, press the button (E) on the rotary
switch (3) and simultaneously turn the rotary
switch (3) to position A.
For hammer drilling, press the button (E) on the
rotary switch (3) and simultaneously turn the
rotary switch (3) to position B.
For chiseling, press the button (E) on the rotary
switch (3) and simultaneously turn the rotary
switch (3) to position C. In switch position C the
chisel is not locked.
For chiseling, press the button (E) on the rotary
switch (3) and simultaneously turn the rotary
switch (3) to position D. The chisel is locked in
position D.
Important.
Only low pressure is required for hammer drilling.
Excessive pressure will exert an unnecessary force
on the motor. Check the drill bits at regular intervals.
Sharpen or replace blunt drill bits.
7. Replacing the power cable
If the power cable for this equipment is damaged, it
must be replaced by the manufacturer or its after-
sales service or similarly trained personnel to avoid
danger.
8. Cleaning, maintenance and
ordering of spare parts
Always pull out the mains power plug before starting
any cleaning work.
8.1 Cleaning
Keep all safety devices, air vents and the motor
housing free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it
with compressed air at low pressure.
We recommend that you clean the device
immediately each time you have finished using it.
Clean the equipment regularly with a moist cloth
and some soft soap. Do not use cleaning agents
or solvents; these could attack the plastic parts of
the equipment. Ensure that no water can seep
into the device.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualified electrician.
Important! The carbon brushes should not be rep
laced by anyone but a qualified electrician.
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
Type of machine
Article number of the machine
Identification number of the machine
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
9. Disposal and recycling
The unit is supplied in packaging to prevent its being
damaged in transit. This packaging is raw material
and can therefore be reused or can be returned to
the raw material system.
The unit and its accessories are made of various
types of material, such as metal and plastic.
Defective components must be disposed of as
special waste. Ask your dealer or your local council.
Anleitung_BT_RH_920E_SPK1:_ 15.10.2008 13:07 Uhr Seite 12
Содержание BT-RH 920 E
Страница 3: ...3 1 2 1 2 10 11 6 7 3 6 5 7 9 3 4 8 6 10 10 Anleitung_BT_RH_920E_SPK1 _ 15 10 2008 13 07 Uhr Seite 3...
Страница 4: ...4 4 6 7 2 5 2 8 3 E 4 A B 11 8 9 B A C D Anleitung_BT_RH_920E_SPK1 _ 15 10 2008 13 07 Uhr Seite 4...
Страница 48: ...48 Anleitung_BT_RH_920E_SPK1 _ 15 10 2008 13 07 Uhr Seite 48...
Страница 49: ...49 Anleitung_BT_RH_920E_SPK1 _ 15 10 2008 13 07 Uhr Seite 49...