5. Technical data
z
H
0
5
~
V
0
3
2
:
e
g
a
tl
o
v
d
e
t
a
R
Power rating:
240 W S2 30 min
Idle speed n
0
n
i
m
0
0
8
2
:
-1
Grinding wheel diameter:
150 mm
Grinding wheel thickness:
20 mm
Grinding wheel hole diameter:
12.7 mm
Max. peripheral speed:
21.98 m/s
Sanding/grinding belt
50 x 686 mm
g
k
2
.
7
:t
h
g
i
e
W
Load factor:
A load factor of S2 30 min (intermittent periodic duty)
means that you may operate the motor continuously
at its nominal power level (240 W) for no longer than
the time stipulated on the specifications label (30
minutes ON period). If you fail to observe this time
limit the motor will overheat. During the OFF period
the motor will cool again to its starting temperature.
Sound and vibration
Sound and vibration values were measured in
accordance with EN 61029.
L
pA
sound pressure level
70,8 dB(A)
K
pA
B
d
3
y
t
n
i
a
t
r
e
c
n
u
L
WA
sound power level
83,8 dB(A)
K
WA
B
d
3
y
t
n
i
a
t
r
e
c
n
u
Wear ear-muffs.
The impact of noise can cause damage to hearing.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever
necessary.
Switch the appliance off when it is not in use.
Wear protective gloves.
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain residual
risks cannot be rules out. The following hazards
may arise in connection with the equipment’s
construction and layout:
1. Lung damage if no suitable protective dust mask
is used.
2. Damage to hearing if no suitable ear protection is
used.
3. Health damage caused by hand-arm vibrations if
the equipment is used over a prolonged period or
is not properly guided and maintained.
6. Before starting the equipment
Pull the power plug before doing any
maintenance or assembly work on the
equipment.
The machine must be set up so that it stands
firmly, i.e. it must be securely screwed to a work
bench or similar.
All covers and safety devices have to be properly
fitted before the machine is switched on.
It must be possible for the grinding wheel to run
freely.
Check that the voltage on the rating plate is the
same as your supply voltage before you connect
the machine to the power supply.
6.1 Assembling the spark deflector
(Figs. 1/3/4/5/6)
Slide the spark detector (3) under the safety hood
(4). Screw the spark deflector (3) to the safety
hood from above (4) using the screws (15).
Adjust the spark deflector (3) using the adjusting
screw (10) so that the distance between the dry
grinding wheel (5) and the spark deflector (3) is
as small as possible and certainly does not
exceed 2 mm.
Adjust the spark deflector (3) periodically to
compensate for wear on the wheel.
6.2 Fitting the workpiece supports
(Fig. 7-8 / Item 7)
Undo the fastening screws (6). Secure the
workpiece supports (7) to the grinder/sander
using the fastening screws (6).
7
GB
^åäÉáí ì åÖ| _q| r p| OQM| pmhNW| ==OTKMRKOMNM==NRWOO=r Üê==pÉáí É=NO
