GB
- 7 -
38. Conversions, adjustments, measurements
and cleaning jobs are to be performed only
when the motor is switched o
ff
. - Pull out the
power plug!
39. Before you switch on the machine, check that
all wrenches and adjustment tools have been
removed.
40. When you leave your workplace, switch o
ff
the motor and pull out the power plug.
41. Electric installation work, repairs and
maintenance are to be carried out only by
specialists.
42. All guards and safety devices have to be
re
fi
tted immediately after completion of any
repairs or maintenance.
43. It is imperative to observe the manufacturer’s
safety, operating and maintenance instruc-
tions as well as the dimensions quoted in the
technical data.
44. It is imperative to observe the accident
prevention regulations in force in your area as
well as all other generally recognized rules of
safety.
45. The machine is designed for indoor installati-
on only.
46. Workpieces smaller than the blade guard may
lead to injuries to your hands and
fi
ngers. Use
suitable aids!
47. When guiding the workpiece do not place
your hands in cramped or awkward positions
where they may slip directly against the blade.
48. Always insert the blade so that the teeth point
down toward the table.
49. To avoid broken blades, always set the cor-
rect blade tension.
50. Be particularly careful when sawing material
with irregular cutting pro
fi
les.
51. Take special care when cutting round work-
pieces such as rods or tubes as they may roll
away from the blade and cause the teeth to
jam. Secure such workpieces with a wedge.
52. When you withdraw the workpiece the teeth
may get caught in the kerf, particularly if the
gap is blocked by sawdust. If this happens
you should switch o
ff
the saw, pull out the po-
wer plug, open the kerf with a wedge and pull
the workpiece free.
53. Never leave your workplace without switching
o
ff
the saw
fi
rst. Wait until the saw stops.
54. Never arrange, glue or assemble any parts on
the work table while the saw is running.
55. Do not switch on the saw until you have
cleared all material remnants and tools from
the work table. Only the workpiece and any
essential aids (wedge) are to be left on the
workpiece.
56. Always wear safety goggles.
57. Keep your
fi
ngers a safe distance from the
blade.
58. Guide the workpiece securely and
fi
rmly and
do not loosen your grip at any time.
59. Never leave your workplace without switching
o
ff
the saw
fi
rst.
60. DO NOT ALLOW YOUR FAMILIARITY WITH
THE SAW TO TURN INTO CARELESSNESS.
IT TAKES ONLY FRACTIONS OF A SECOND
FOR CARELESSNESS TO RESULT IN SE-
RIOUS INJURIES.
2. Layout and items supplied
2.1 Layout (Fig. 1-4)
1 Hexagon key 4 mm
2 On/O
ff
switch
3 Blade speed regulator
4 Cover,
left
5 Locking
screw
6 Dial
scale
7 Saw
table
8 Blade holder, bottom
9 Retention
bolt
10 Blade guard
11 Clamping screw
12 Holder
13 Blade holder, top
14 Clamp lever
15 Blade
16 Blow-o
ff
device
17. Pointer
18. Table insert
19. Arm
20. Screw
21. Workpiece hold-down device
22. Spare saw blade
23. Dust extraction adapter
24. Hexagon key 3mm
2.2 Items supplied
Please check that the article is complete as spe-
ci
fi
ed in the scope of delivery. If parts are missing,
please contact our service center or the nearest
branch of the DIY store where you made your
purchase at the latest within 5 work days after
purchasing the article and upon presentation of
a valid bill of purchase. Also, refer to the warranty
table in the warranty provisions at the end of the
operating instructions.
•
Open the packaging and take out the equip-
Anl_TC_SS_405_E_GB_Korea.indb 7
Anl_TC_SS_405_E_GB_Korea.indb 7
20.07.2022 14:06:30
20.07.2022 14:06:30
