EINHELL 43.072.00, Руководство по эксплуатации

Страница: 27 / 76

3) and tilt the machine head to the left using the
handle (Fig. 29 / Item 16) until the pointer (Fig. 28
/ Item 33) points to the required angle on the
scale (Fig. 28 / Item 34).
앬 The angle adjustment lever is fitted with a
free-wheel function. To actuate it, pull the
handle backwards (applying
counterpressure with your thumb on the
shaft) and turn it.
앬 Tighten the angle adjustment lever against and
complete the cut as described in point A (Fig. 29).
D. Miter cut 0°- 45° and turntable 0°- 45° (Fig. 30)
In crosscut and miter saw mode it is possible to make
miter cuts to the left at angles of 0° – 45° and at the
same time angle cuts to the left and right at angles of
0° – 45° (double miter cuts).
앬 Move the machine head (17) to its upper position.
앬 Release the turntable (19) by releasing the
locking lever.
앬 Set the turntable to the required angle using the
handle (16). (see also point B)
앬 Tighten the locking lever again to secure the
turntable.
앬
Release the angle adjustment lever (Fig. 28 / Item
3) and tilt the machine head to the left using the
handle (Fig. 29 / Item 16) until the pointer (Fig. 28
/ Item 33) points to the required angle on the
scale (Fig. 28 / Item 34) (see also 7.2.3/C).
앬 Tighten the angle adjustment lever against and
complete the cut as described in point A (Fig. 30).
E. Dust bag (Fig. 1 + 2 / Item 1)
The saw is equipped with a debris bag for sawdust
and chips. This bag can be emptied using the zip
fastener at the bottom.
7.3 Bench circular saw
7.3.1 Conversion work for use as a bench
circular saw
1. The saw is set up for use as a crosscut and miter
saw.
2. If necessary release the locking lever (Fig. 31 /
Item 30), turn the turntable to the 0° position and
secure it there using the locking lever (see also
7.2.3/B).
3. Release the angle adjustment lever (Fig. 31 / Item
3), set the angle to 0° and secure it again with the
angle adjustment lever (see also 7.2.3/C).
4. If necessary set the stop rails so that they do not
project over the bench and also so that they do
not cover the slot in the bench for the saw blade
(see also 7.2.1/19).
5. Release the retaining nut (Fig. 32 / Item 26) for
the splitter (Fig. 32 / Item 12), swing the splitter
downwards (Fig. 33) and tighten the retaining nut
again (Fig. 34). The splitter must be in line with
the saw blade.
6. Remove the chip box (20). To do this, push the
Allen screw upwards (Fig. 20) and turn it through
90°, after which the chip box (20) can be
removed.
7. Pull out the locking pin (Fig. 31 / Item 25) for
height adjustment and turn it through 90°. Then
press the lowering lock and slowly lower the
machine head (17) until it locks into position.
8. Turn the knurled screw (Fig. 31 / Item 13) as far
as possible clockwise to move the saw blade (4)
into its highest position.
9. Pull the lever (Fig. 35 / Item 24) towards yourself
and carefully swing the saw over (Fig. 36).
Important. When you swing the saw bench, there
is a risk of suffering crush injuries to your hands
and finger. Only touch the saw bench at the front
and rear when swinging it. Do not reach between
the saw bench and the side parts. Hold the
bench securely as you swing it. Ensure that the
lever engages fully again after you have swung
the saw bench and that the bench is locked into
position.
10. Turn the knurled screw (Fig. 31 / Item 13) as far
as possible anti-clockwise to move the saw blade
to its highest position for bench circular saw
mode.
11. Fit the saw blade guard (11) (Fig. 37 – 39). To do
this, remove the nut (Fig. 38 / Item 35), washer
(Fig. 38 / Item 36) and the screw (Fig. 37 / Item
37) from the saw blade guard. Then move the
saw blade guard over the splitter (12) so that the
holes in the saw blade guard and splitter line up.
Now secure the saw blade guard to the splitter
using the screw, washer and nut (Fig. 39). To
dismantle, proceed in reverse order.
12. Connect the chip extractor connector on the saw
blade guard (11) to a suitable extraction system.
27
GB
Anleitung NKT 1200_SPK1:_ 28.03.2007 11:55 Uhr Seite 27