EINHELL 3400622, Оригинальная инструкция по эксплуатации

Страница: 22 / 36

GB
- 22 -
Fitting the grass basket to the tractor lawn
mower (Fig. 25-29)
•
Fig. 25-26: Attach the grass basket to the at-
tachment points (Item e).
•
Fig. 27: Note that the marking arrows are op-
posite each other.
•
Fig. 28: Before you can close the grass bas-
ket you have to open it fully so that it latches
completely into the attachment points.
•
Fig. 29: Lock the grass basket by exerting
slight pressure on the rear handle.
6. Operation
Note:
For detailed information on starting the engine, re-
fer to the enclosed manual from Briggs & Stratton.
Important.
The engine does not come with oil in it. Therefore,
be sure to add oil before starting the engine for
the fi rst time. You will also need to fi ll in petrol, as
this is also not supplied upon delivery.
Whenever you need to perform any adjustment
and/or repair work on your lawn mower, wait until
the blade has come to a complete stop. Always
switch o ff the engine before carrying out any ad-
justments, maintenance or repairs.
Warning: Never use more than one safety petrol
can. Do not smoke when refueling. Switch o ff the
engine before refueling and allow the engine to
cool down for a few minutes.
Safety switch
To prevent injuries from improper use, the lawn
mower is equipped with various safety devices.
To be able to start the engine, the following condi-
tions must be met:
•
Gear position → neutral
•
The mower unit must be switched off.
•
The operator must be sat on the seat.
•
The locking brake must be applied.
The engine cuts automatically whenever the ope-
rator leaves the seat.
Each time before use, check the tire pressure
and oil level.
Speed lever (Fig. 30)
Move the throttle lever (Item 14) in order to incre-
ase or decrease the engine speed. For optimum
mowing results we recommend that the throttle
lever should be set to the “Hare” position.
Tortoise = Slow
Hare = Fast
“ ” = Choke (enables a quick cold start)
Lights (Fig. 30):
Vehicle lights ON/OFF (Item 15).
Note: The lights only work if the ignition lock is in
the “ON” position.
Mower unit switch (Fig. 31)
Use the ON/OFF switch for the mower unit (Item
16) to start the mower unit.
“I” = On
“O”= O ff
Pay attention to the safety instructions.
Ignition lock (Fig. 31/Item 17)
Settings:
STOP= Turning o ff the engine
ON=Turning on the ignition
START=Starting the engine
Changing the fuse (Fig. 32)
If the 10A fuse (Item 32) is defective, replace it as
illustrated.
Important.
A defective fuse is always the result of a fault in
the electrical system. A check should be carried
out by an authorized service center.
Cutting height adjustment (Fig. 33)
Use the cutting height adjuster lever (Item 3) to
adjust the cutting height. Actuate the lever as
illustrated.
Locking brake (Fig. 34-35)
To actuate the locking brake, press the brake pe-
dal (Item 13) down. To lock the brake pedal in the
brake position, press the locking brake (Item 12).
To release the locking brake, press brie fl y on the
brake pedal (Item 13).
Note: The engine can only be started if the lo-
cking brake is applied.
Accelerator pedal (Fig. 36-37)
The accelerator pedal (forward) (Item 7) and the
accelerator pedal (reverse) (Item 6) are for cont-
rolling the driving direction and speed.
Note: Release the locking brake fi rst.
F → Forward
Anl_GE_TM_102_BS_SPK8.indb 22 Anl_GE_TM_102_BS_SPK8.indb 22 27.11.12 12:38 27.11.12 12:38