Eiki EK-830U, Руководство пользователя, Страница: 9 / 78

Usage Notice
9
Compliance
FCC Caution
Note: This equipment has been tested and found
to comply with the limits for a Class* digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV
technician for help
Use of shielded cable is required to comply with
Class* limits in Subpart B of Part 15 of FCC Rules.
* See the rating label on the projector if class A or B.
Do not make any changes or modifications to
the equipment unless otherwise specified in the
instructions. If such changes or modifications should
be made, you could be required to stop operation of
the equipment.
Trade Name : EIKI
Responsible party : EIKI International, Inc.
Address : 30251 Esperanza Rancho Santa Margarita
CA 92688-2132
Telephone No. : 800-242-3454 (949-457-0200)
Canadian Radio Interference Regulations:
This digital appraratus meets all requirements of
the Canadian ICES-003.
* See the rating label on the projector if class A or B.
Warning:
A plug with bared flexible cord is hazardous if
engaged in a live socket outlet.
Warning:
This apparatus must be earthed.
The socket-outlet should be installed near the
equipment and easily accessible.
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets
the requirement for use in the country you purchased
it.
AC Power Cord for the United States and Canada:
AC Power Cord used in the United States and Canada
is listed by the Under-writers Laboratories (UL) and
certified by the Canadian Standard Association (CSA).
AC Power Cord has a grounding-type AC line
plug.
This is a safety feature to be sure that the plug will fit
into the power outlet. Do not try to defeat this safety
feature. Should you be unable to insert the plug into
the outlet, contact your electrician.
AC Power Cord for the United Kingdom:
This cord is already fitted with a moulded plug
incorporating a fuse, the value of which is indicated
on the pin face of the plug. Should the fuse need to
be replaced, an ASTA approved BS 1362 fuse must
be used of the same rating, marked thus . If the
fuse cover is detachable, never use the plug with the
cover omitted. If a replacement fuse cover is required,
ensure it is of the same colour as that visible on the
pin face of the plug (i.e. red or orange). Fuse covers
are available from the Parts Department indicated in
your User Instructions.
If the plug supplied is not suitable for your socket
outlet, it should be cut off and destroyed. The end of
the flexible cord should be suitably prepared and the
correct plug fitted.
The Wires in this mains lead are coloured in
accordance with the following code:
• Green-and-yellow ......... Earth
• Blue .............................. Neutral
• Brown ........................... Live
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured
markings identifying the terminals in your plug
proceed as follows:
• The wire which is coloured green-and-yellow must
be connected to the terminal in the plug which is
marked by the letter E or by the safety earth symbol
or coloured green or green-and-yellow.
• The wire which is coloured blue must be connected
to the terminal which is marked with the letter N or
coloured black.
• The wire which is coloured brown must be
connected to the terminal which is marked with the
letter L or coloured red.