background image

9      Troubleshooting

 

 

                                                                                                    Page    18  /  25 

9.Troubleshooting 

 

When trouble is found, check the following points before contacting your distributor. 
If none of these are applicable or the trouble is not remedied even after action has 
been taken, the product may have failed. Contact your distributor. 

 

Problem 

Cause 

Solution 

Ref. 
chap 

The power is not 
turned on. 

The battery is flat. 

Charge the battery. 

7.1 

Press  the  power  switch  too 
short time. 

Long  press  the  power 
switch. 

The power LED 
on charge base 
does not light. 

Using a wrong adapter. 

Use 

the 

original 

adapter. 

4.3 

The 

adapter 

is 

not 

connected. 

Check the connection. 

4.3 

The plug of the adapter is not 
inserted into the outlet. 

Check the connection. 

There  is  no  electricity  in  the 
outlet. 

Check the connection. 

No charge 
indicator flash 
on handpiece 
screen 

Put  the  handpiece  into  the 
charge  base  in  the  wrong 
direction. 

Check the direction. 

4.3 

Charge  pin  of  charge  base 
unable to rebound. 

Remove  debris  which 
between move part and 
base of the charge pin. 

Contactors are dirty. 

Cleaning the surface of 
contactors. 

The charge base broken. 

Using  adapter  connect 
to  handpiece  directly, 
and 

Contact 

your 

distributor. 

Handpiece 
screen does not 
appear 

The handpiece broken. 

Check if there is a sound 
of  beep  or  motor,  and 

Contact 

your 

distributor.

 

No sound. 

Beep volume set to 0. 

Set beep volume to 1, 2 
or 3. 

6.2 

 

Содержание Fast-Pack


























Отзывы: