background image

2

The Ei140RC series is supplied with an Easi-Fit 

base that allows very quick and simple installation 

of the Smoke Alarm, combined with simple detector 

head removal and replacement. The Easi-Fit base 

automatically connects both mains power and battery 

as the detector head slides on to the Easi-Fit base.
Up to 12 Smoke/Heat Alarms can be interconnected so 

that when one senses fire all the units alarm.
Interconnection can be achieved by hardwire or through 

a RadioLINK Base, the Ei168RC.
A green LED indicates the presence of mains power. A 

red LED will flash rapidly in an alarm scenario.
All Alarms feature a combined test/hush button.
The “Test/Hush” button will either silence false alarms 

or perform a unit self-test.
In “Test” mode the Alarm will perform a self-test and 

sound the horn. 
In “Hush” mode the Alarm will be silenced for a period 

of approximately ten minutes to overcome false alarm 

conditions. It will then automatically reset itself.

The Ei140RC series may be interconnected with any 

other Ei Electronics RadioLINK or RadioLINK

+

 products 

through fiiting onto an Ei168RC RadioLINK Base. 

This base will enable the Ei140RC series Alarms to 

communicate RF messages to other Ei Electronics 

products such as the Ei450 RadioLINK Alarm Controller 

where you can remotely locate, test and hush your 

Ei140RC Series Alarms using this wireless controller.
For detailed user instructions on using the RF 

interconnection base Ei168RC with the Ei140RC series, 

please consult the Ei168RC instruction manual.

Important Information

Do’s

Don’ts

Regularly check green mains 

indicator is lit

Do not paint your Alarm. Do 

not allow paint, water or dust 

to contaminate the Alarm

Test Weekly  –  See  testing 

and maintenance

Your  Alarm  is  powered  by 

230VAC.  Do  not  open  or 

insert anything into the Alarm

If  nuisance  alarms occur  – 

press the test/hush button to 

silence the Alarm for 10 mins

Remove or completely cover 

your Alarm  when  decorating 

to  prevent  dust  or  other 

contamination  damaging  the 

unit

Clean your Alarm regularly

RF Interconnection

Introduction to Ei140RC
Smoke/Heat Alarms

User Section

Содержание Aico Ei140RC





















Отзывы: