EHC Fusion E10 Combi Series Скачать руководство пользователя страница 23

Страница: 23 / 33

EHC

Fusion E10 Combi

–

Installation and technical manual

Page 23

14.

Commisioning: Programmer/Cont.

Setting the date and time

Press the

SET

button and the clock icon on the screen will flash. Press the

buttons to

adjust the time. Hold down the button to change the time quicker.

Press

SET

button till the

Y:00

icon (year) appears and the letter

flashes. Press the

button to set the year. Press

NEXT

, and

N:00

appears (month). Press

button to set

month. Press Next.

d:00

appears (day). Press

button to set day.

NOTE:The unit will automatically return to run mode if a period of 5 minutes passes without
any buttons being pressed.

Changing programme times

The built-in programmes for Central heating and Hot water can be easily changed to better
suit your needs.

To change the Central Heating programme, press

SET

until the radiator icon flashes in the screen and

1 ON

appears. This indicates the time shown on the display is
the first ON time. Change this to the required ON time by
pressing the +/- buttons.

Press

NEXT

button, the display will now show

1 OFF

. Change as before.

Use

NEXT

and

buttons in this way to programme the second time period.

If the unit is set for 3 ON/OFF periods, the number

will appear. This is set in exactly the

same way as the previous first and second time period.

Содержание Fusion E10 Combi Series


































Результаты поиска

Содержание Fusion E10 Combi Series

Отзывы:

EHC Fusion E10 Combi Series, Инструкция по установке и техническое руководство, Страница: 23 / 33

Результаты поиска

Содержание Fusion E10 Combi Series

Отзывы: