EHC Fusion E10 Combi Series Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 33

EHC Fusion E10 Combi Series Скачать руководство пользователя страница 1

EHC Fusion E10 Combi Series

Combination Boiler Range

Installation and

technical manual

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND

RETAINED FOR FUTURE REFERENCE.

The Fusion E10 must be installed by a competent person with accordance
with this installation manual and all relevant regualtions in force at time of
installation

The Fusion E10 combination unit’s Unvented Cylinder is a controlled service
as defined in the latest edition of the building regulations.
The relevant regulations are:

England and Wales – Building Regulation G3
Scotland – Technical Standard P3
N Ireland – Building Regulation P5

After installation the Benchmark log table on page X must be completed
and left with the householder for future reference.

The Electric Heating Company Ltd

Unit 40, Block 5, Third Road, Blantyre Industrial Estate, Blantyre, Glasgow, G72 0UP

Tel. 01698 820533
Fax. 01698 825697

[email protected]

www.electric-heatingcompany.co.uk

1
2
3
...
»

Содержание Fusion E10 Combi Series


































Отзывы:

Нет отзывов