background image

8

SEACLIFF 

Ceiling Fan

CODE LEARNING MODE:

The remote control has been pre-paired with the fan for your convenience, however should you ever need to replace the remote control 
or re-paired / re-synced if multiple fans are located within an area, follow these simple steps: 

SINGLE FAN INSTALLATION:

1.

Connect wiring and switch the power supply ON, the receiver will make a beep sound.

2.

Within 30 seconds

, press and hold FAN OFF button for 10 seconds or until a  beep sound is heard meaning pairing/syncing

has been successful. 

Note:

 This must be done prior to fixing canopy in place.

3.

Operate and test. 

Note:

 Blades must be attached or fan will not continue to operate.

4.

Complete assembly of canopy.

MULTIPLE FAN INSTALLATION:
Important:

 The pairing/syncing of each fan and remote MUST be done with all other fans disconnected from the power supply.

1.

Fan #1 - Connect wiring and switch the power supply ON, the receiver will make a beep sound.

2.

Within 30 seconds

, press and hold FAN OFF button for 10 seconds or until a  beep sound is heard meaning pairing/syncing

has been successful. 

Note:

 This must be done prior to fixing canopy in place.

3.

Operate and test. 

Note:

 Blades must be attached or fan will not continue to operate.

4.

DO NOT complete assembly of fan #1. Disconnect fan #1 from the power supply, or unplug the receiver to disconnect from terminal block.

5.

Repeat steps 1-3 for each subsequent fan.

6.

Only once all fans have been paired/synced and successful tested on separate remote control transmitters, can all fans then be
reconnected to power, and assembly of canopy completed.

Note:

 If the remote does not pair/sync, disconnect power from fan and leave disconnected for 60 seconds, before reconnecting and 

starting steps 1-3 again. Disconnection from power supply must be for minimum of 60 seconds.

If the transmitter and receiver are not working or working properly, check:
1.

The battery is in the correct position and making good contact, and replace batteries if necessary.

2.

Is there any other radio frequency or remote-controlled devices nearby, devices using the same frequency can interfere with each device?

3.

Low voltage in the batteries can affect the operation and signal reception. The LED indicator light will flash when
the battery is low, replace the battery immediately.

Note:

 If not using the fan and remote for extended periods, remove the battery from the transmitter.

OPERATING YOUR REMOTE CONTROL (NON-LIGHT MODELS): 

1. LED indicator light
2. Turn the fan OFF
3. Fan speeds (1=Low & Night Mode, 5=Hight)
4. Timer control for the fan (30min=Fan stops after 30Minutes, 8H=Fan stops after 8 Hours)
5. Battery for transmitter
6. Direction of the fan (Forward/Reverse)

Night mode*

 – Press “1 (low speed)” and hold for 3 seconds to operate.

Forward / Reverse

* – Press “F/R ” to operate. 

Press while fan running and hold for 

3-5 seconds or untilor beep is heard. Fan will slowly stop, then reverse at the same speed)

OPERATING YOUR REMOTE CONTROL (LIGHT MODELS): 

1. Turns fan OFF
2. Colour Temperature:

  Warm White           

  Neutral White       

   Cool White

3. Fan Speed & ON:

4. Increase Brightness (+)/

Speed 1 (Low)

Decrease Brightness (-)

and Night Mode* ‚
2 - Speed 2

5. Timer:

3 - Speed 3

2H - Fan turns off after 2 Hours

4 - Speed 4

8H - Fan turns off after 8 Hours

5 - Speed 5 (High)

6. Turns light ON & OFF
7. Forward / Reverse
8. Natural Breeze

 Night mode*

 – Press “1 (low speed)” and hold for 3 seconds to operate.

6

8

7

1

2

3

4

5

8H

2H

+

LED

-

LED

F/R

5

4

3

2

1

LIGHT

ON/OFF

FAN
OFF

NATURAL

WIND

FAN

    OFF

LIGHT

ON/OFF

1

3

5

2

4

1H

2H

F/R

4H

8H

1

7

5

2

3

4

6

FAN

    OFF

1

3

5

2

4

1H

2H

F/R

4H

8H

1

5

2

3

4

6

Stradbroke , Torquay
WITH LIGHT -REMOTE

Stradbroke , Torquay, Seacliff
NO LIGHT -REMOTE

30min

Содержание SEACLIFF 20523401



















Отзывы: