manualshive.com logo in svg

Eggtimer Rocketry Rev A4a, Инструкция по сборке и эксплуатации

Поделиться
Скачать
Eggtimer Rocketry Rev A4a Скачать руководство пользователя страница 32

 

Troubleshooting Tips (in approximate order of likelihood) 

 
No power-on blinks from the PWR LED 
 
•  Battery cable connected incorrectly 
(Match “+” and “-“ on the INPUT side with your battery connector) 
•  Bad solder joint on voltage regulator 
•  Bad solder joint on 10 uF capacitors 
•  Bad solder joint on the ESP8266-12 module 
•  LED mounted backwards (long lead needs to be on the “+” side) 
• Weak battery 
 
 
No data when I connect the USB-Serial cable 
•  Serial cable connected incorrectly 
•  Terminal program not configured correctly 
    (should be 115,200 baud, 8 bits, no parity, 1 stop bit) 
• Bad solder joint on ESP8266-12 module 
• Bad solder joint on header 
 
Don’t see an “WIFI_SW_…” SSID 
• Bad solder joint on ESP8266-12 module 
• Weak battery 
 
 
Can’t connect to “WIFI_SWITCH…” SSID 
•  Bad passkey (hook up the serial cable and check it) 
•  Wrong type/encryption selected  
    (set them all to “auto” and let your WiFi manager pick it up) 
 
Can’t bring up WiFi Switch web page 
•  Bad WiFi connection (check your WiFi manager) 
•  Incorrect URL (use 

http://192.168.4.1

 ) 

•  Weak battery (use a freshly charged one) 
 
 
Switch won’t turn on when I enter the code and click Submit 
• Bad solder joint on the “ON” LED or LED reversed 
• Bad solder joint on 4.7K resistor next to the ON LED 
• Bad solder joint on the ESP8266-12 module 
• Bad solder joint on the MOSFET 
• Bad solder joint on the 10K resistor next to the MOSFET 
• Weak battery 
 
 
 
 

Содержание Rev A4a



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды