55
RESOLUCIÓN DE PROBLEMAS
ATENCIÓN: parar la unidad y desconectar la bujía antes de realizar todas las
pruebas correctivas recomendadas en la tabla siguiente, a no ser que sea
necesario el funcionamiento de la unidad.
Una vez verificadas todas las posibles causas, si el problema no se resuelve, llamar a un Centro
de Asistencia Autorizado. Si se observa un problema no listado en esta tabla, llamar a un
Centro de Asistencia Autorizado.
PROBLEMA
POSIBLES CAUSAS
SOLUCIÓN
El motor no arranca o se apaga a
los pocos segundos del arranque.
(Comprobar que el interruptor
esté en "I")
1. No hay chispa
2. Motor
atascado
1. Controlar la chispa de la bujía. Si no hay
chispa, repetir la prueba con una bujía
nueva (BPMR7A).
2. Seguir el procedimiento de la pág.21.
Si el motor no arranca, repetir el
procedimiento con una bujía nueva.
El motor arranca, pero no acelera
correctamente o no funciona
correctamente a alta velocidad.
Es necesario regular el carburador.
Llamar a un Centro de Asistencia Autorizado
para regular el carburador.
El motor no alcanza la máxima
velocidad y/o emite demasiado
humo.
1. Controlar la mezcla aceite-gasolina.
2. Filtro de aire sucio.
3. Es necesario regular el carburador.
1. Utilizar gasolina fresca y un aceite adecuado
para motores de 2 tiempos.
2. Limpiar; leer las instrucciones del capítulo
Mantenimiento del filtro de aire.
3. Llamar a un Centro de Asistencia Autorizado
para regular el carburador.
El motor arranca, gira y acelera,
pero no mantiene el mínimo.
Es necesario regular el carburador.
Regular el tornillo del mínimo "T" (Fig.84,
pág.39) en sentido horario para aumentar la
velocidad; consultar el capítulo Mantenimiento
del carburador.
La barra y la cadena se calientan
y emiten humo durante el
funcionamiento
1. Depósito de aceite de la cadena
vacío
2. Cadena demasiado tensa
3. Malfuncionamiento del sistema de
lubricación
1. El depósito de aceite se debe llenar cada vez
que se llene el depósito de combustible.
2. Tensado de la cadena; ver las instrucciones en
el capítulo Montaje de la barra y la cadena
(Pág.13).
3. Hacer funcionar a pleno régimen 15-30
segundos. Detener y comprobar que el
aceite gotee desde la punta de la barra. Si
hay aceite, el malfuncionamiento puede
deberse a que la cadena está floja o la barra
está dañada. Si no hay aceite, contactar con
un Centro de Asistencia Autorizado
El motor arranca y funciona, pero
la cadena no gira
1. Freno cadena activado
2. Cadena demasiado tensa
3. Ensamblaje barra y cadena
4. Cadena y/o barra dañadas
5. Embrague y/o piñón dañados
1. Desactivar el freno de la cadena; ver el capítulo
Uso – Freno cadena (Pág.27)
2. Tensado de la cadena; ver las instrucciones en
el capítulo Montaje de la barra y la cadena
(Pág.13)
3. Ver las instrucciones en el capítulo Montaje de
la barra y la cadena (Pág.13)
4. Ver las instrucciones en el capítulo
Mantenimiento barra y/o cadena (Pág.35)
5. Sustituir si es necesario; contactar con un
Centro de Asistencia Autorizado
ATENCIÓN: no tocar
n u n c a l a c a d e n a
cuando el motor esté
en funcionamiento
OPLOSSEN VAN PROBLEMEN
WAARSCHUWING: zet het apparaat altijd uit en koppel de bougie los voordat u de
aanbevolen corrigerende maatregelen in onderstaande tabel uitvoert, behalve
als gevraagd wordt om het apparaat aan te zetten.
Als alle mogelijke oorzaken nagegaan zijn en het probleem nog steeds niet is opgelost, neem
dan contact op met een erkend reparatiecentrum. Als u een probleem heeft dat niet in deze
tabel staat, neem dan contact op met een erkend reparatiecentrum.
PROBLEEM
MOGELIJKE OORZAKEN
OPLOSSING
De motor start niet of gaat na
enkele seconden na het starten
weer uit. (Controleer of de
schakelaar in stand "I" staat)
1. Er is geen vonk
2. Motor is verzopen
1. Controleer de vonk van de bougie. Als er
geen vonk is, herhaal de test dan met
een nieuwe bougie (BPMR7A).
2. Volg de procedure op pag.21. Als de motor
nog niet start, herhaal de procedure dan
met een nieuwe bougie.
De motor start, maar versnelt niet
voldoende of werkt niet goed bij
hoge snelheid.
De carburateur moet worden
afgesteld.
N e e m co n t a c t o p m e t e e n e r k e n d
reparatiecentrum om de carburateur te
laten afstellen.
De motor bereikt de volledige
snelheid niet en/of geeft zeer veel
rook af.
1. Controleer het olie-/
benzinemengsel.
2. Luchtfi lter is vuil.
3. De carburateur moet worden
afgesteld.
1. Gebruik verse benzine en een olie die
geschikt is voor tweetaktmotoren.
2. Schoonmaken; zie de instructies in het
hoofdstuk Onderhoud van het luchtfilter.
3. Neem contact op met een erkend reparatiecentrum
om de carburateur te laten afstellen.
De motor start, draait en versnelt,
maar wil niet stationair lopen.
De carburateur moet worden
afgesteld
Stel de stationairstelschroef "T" (Fig.84,
pag.39) naar links bij om de snelheid te
verhogen; zie het hoofdstuk Onderhoud
carburateur.
Het zaagblad en de ketting
warmen op en beginnen te roken
tijdens het werken
1. Olietank ketting leeg
2. Kettingspanning te strak
3. Defect van het smeringssysteem
1. De olietank moet gevuld worden telkens de
brandstoftank wordt gevuld.
2. Kettingspanning; zie de instructies in het
hoofdstuk Zaagblad- en kettingmontage
(Pag.13).
3. Laat gedurende 15-30 seconden met volledig
geopend gas werken. Sluit en controleer
of er olie van de punt van het zaagblad
druipt. Indien er olie aanwezig is, kan het
defect te wijten zijn aan een losse ketting
of een beschadigd zaagblad. Indien er
geen olie is, neem dan contact op met
een Erkende Hersteller
De motor start en loopt, maar de
ketting draait niet
1. Kettingrem
ingeschakeld
2. Kettingspanning te strak
3. Assemblage zaagblad en ketting
4. Ketting en/of zaagblad beschadigd
5. Koppeling en/of tandwiel
beschadigd
1. Schakel de kettingrem uit; zie hoofdstuk
Gebruik – Kettingrem (Pag.27)
2. Kettingspanning; zie de instructies in het
hoofdstuk Zaagblad- en kettingmontage
(Pag.13)
3. Zie de instructies in het hoofdstuk Zaagblad- en
kettingmontage (Pag.13)
4. Zie de instructies in het hoofdstuk Onderhoud
zaagblad en/of ketting (Pag.35)
5. Vervang ze indien nodig; neem contact op met
een Erkende Hersteller
WAARSCHUWING: raak
de ketting nooit aan
wanneer de motor in
werking is