Edwards IBV16MKS Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 16

Edwards IBV16MKS Скачать руководство пользователя страница 9

© Edwards Limited 2014. All rights reserved.

Page 5

Edwards and the Edwards logo are trademarks of Edwards Limited.

Maintenance

C360-00-880 Issue E

5

Maintenance

5.1

General information

The IBV ball valves are designed to require little user maintenance. Edwards recommends periodic cleaning and
adjustment of the valve operating shaft gland nut after approximately 30,000 cycles. There are no parts available
for spares, as removal and refitting of the seals requires specialised factory tooling.

5.2

Safety information

Observe all appropriate safety precautions when performing maintenance on a valve from a system which has pumped
dangerous process substances.

Ensure that maintenance is performed in a well ventilated area.

Do not use abrasive or reactive chemical substances to clean the valve. Do not use solvents to clean the seals.

Dispose of all components which have been contaminated by dangerous process substances in a safe manner.

5.3

Fault finding

Table 2 - Fault finding

Symptoms

Check

Valve will not open

Is the valve blocked?

Valve leaks

Is the valve full of debris?
Is the shaft seal nut loose?

«
...
7
8
9
10
11
...
»

Содержание IBV16MKS

















Отзывы:

Нет отзывов